Service HotlineWhen using screws, if you can understand the mechanical properties of screws first, then you can use screws better. Different types of screws have different mechanical properties, and the different mechanical properties lead to different occasions when screws are used. 1. Self-tapping screws: mechanical performance requirements 1. Heart hardness: standard value HRC28-38. When testing, take the section 1-2 times the diameter of the name from the tail. If the length of the name is too short, it can be embedded first, and then the hardness is measured. 2. Surface hardness: standard MIN HV450. 3. Carburized layer: standard 4#-6#: 0.05-0.18mm, 8#-12#: 0.10-0.23 mm, 14#: 0.13-0.28 mm. The main purpose of carburizing is to enhance the surface hardness and ensure the strength of the teeth. If the decarburization is too deep and the carburization is insufficient, the strength of the teeth will not meet the requirements, that is, the teeth will be damaged during the screw-in test. 4. Torque: standard specification 4#5#6#7#8#10#12#14#A tooth 14212835455696145AB tooth 142128354565102165. 5. Screw-in test: screw the self-tapping screw into a steel plate with a reserved test hole. The self-tapping screw should form a matching thread in the test plate, and the thread of the screw itself will not be deformed or damaged until the end. Tapered threads pass completely through the test plate. The screw-in test is only applicable to AB, B, BP and other types of self-tapping screws. It is stipulated in IFI that the test plate shall be prepared from semi-hard low-carbon cold-rolled steel, and the hardness of the steel plate is 70–85HRB in Rockwell. The standard specification of the steel plate, that is, the thickness, is shown in the table below. The test hole should be punched or drilled, and the tolerance is the specified nominal diameter (see the table below) ± 0.025mm. Specifications 6#7#8#10#12#1/4 Test plate thickness (mm) 1.85-1.953.12-3.234.68-4.84 Aperture (mm) ±0.0252.953.263.454.044.765.50.
Fasteners are a class of mechanical parts that are used for fastening connections and are widely used. It is used in a wide range of industries, including energy, electronics, electrical appliances, machinery, chemical industry, metallurgy, mold, hydraulic and other industries, in various machinery, equipment, vehicles, ships, railways, bridges, buildings, structures, tools, instruments, chemicals, instruments And supplies, etc., you can see all kinds of fasteners, which are widely used mechanical basic parts. In the fields of listed rails, construction machinery, etc., due to the harsh application environment, the requirements for fasteners are more stringent. If the fasteners are loosened, it may lead to serious consequences, resulting in a large amount of property damage, even serious life cost.
Wood screws are similar to machine screws, but the thread on the screw is a special thread for wood screws, which can be directly screwed into wooden components (or parts) to connect a metal (or non-metal) part with a through hole to a wood screw. The components are fastened together. This connection is also a detachable connection.
According to an aspect of Guangdong Yueluo Hardware Industry Co., Ltd., a rivet insertion mechanism is provided, including a pressure cylinder, a pressure shaft, an insertion nozzle, a bottom plate, a fixing block and a rivet fixing mechanism, wherein one end of the pressure shaft is connected with the pressure cylinder, and the other end is connected with the pressure cylinder. The insertion nozzle is connected, the fixing block is sleeved on the pressing shaft, and is fixedly connected with the bottom plate, the rivet fixing mechanism is installed on the bottom plate, and the insertion nozzle extends into the rivet fixing mechanism and can extend from the rivet fixing mechanism.
Flat washers are frequently used in mechanical connections. They are usually placed between the nut or screw head and the connected parts to prevent the screw or nut from loosening during use. The upper and lower end faces of conventional flat gaskets are mostly smooth planes, with a single structure and poor compressive capacity. When assembled with a nut or screw, the pressure on the flat washer is increased, and when it is closely rubbed with the nut or screw, it is prone to breakage, which greatly affects the quality of the product.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: solid ball head cylindrical pins, extended hexagon head bolts, chamfered cross bolts, welded studs with welding points and other products, we can provide you with suitable products Your fastener solution.
