Service HotlineRivets are widely used in the fixing of product components, and the process of inserting rivets into products is currently mostly done by manpower. However, relying on manpower to insert rivets has low automation and low efficiency, which is not conducive to large-scale Production.
The motor bearing retaining ring is used to fix the axial position of the bearing. The structure of the bearing retaining ring 1 in the prior art is shown in FIG. 1 , which is a ring-shaped sheet-like structure with a gap, the inner diameter of which is smaller than the inner diameter of the connected bearing, and the outer side 11 of the ring is a continuous arc shape. The inner side of the ring is provided with a groove 12, 13 of the same size on both sides of the midpoint of the ring, and the width of the groove is equal to the distance from the groove to the gap of the ring. When the axial locking force (impact) of the bearing retaining ring of this structure is greater than 6.5N, serious deformation will occur or even the retaining ring will be separated from the shaft shoulder. In order to solve this problem, when the axial locking force is greater than 6.5N, the prior art generally adopts a two-ring combined structure of steel wire ring + bearing retaining ring, and its installation state is shown in Figure 2, as shown in Figure 2, l It is a bearing retaining ring in the prior art, 3 is a locking nut, 4 is a fan blade insert, 5 is a bearing, 6 is a shaft, and 7 is a wire ring. However, such a structure is costly and troublesome to assemble, especially if the bearing retaining ring is not placed in place during assembly, the bearing retaining ring is at risk of being crushed.
Principles of stainless steel screw material selection: The selection of stainless steel materials is mainly considered from the following five aspects. 1. Requirements on mechanical properties, especially strength, of stainless steel screw materials; 2. Requirements on corrosion resistance of materials by working conditions; 3. Heat resistance of materials by working temperature (high temperature strength, oxidation resistance) 4. Requirements for material processing performance in terms of production technology; 5. Other aspects such as weight, price, procurement and many other factors must be considered.
Figure 1 is a schematic structural diagram of Guangdong Yueluo Hardware Industry Co., Ltd. Figure 2 is a front view of the structure of the riveted positioning block. FIG. 3 is a top view of the structure of the riveted positioning block. Figure 4 is a front view of the structure of the riveting lower die. Figure 5 is a side view of the structure of the riveting lower die. 1, I is a rivet, 2 is a riveting positioning block, 3 is a product, 4 is another product, and 5 is a riveting lower die. [0017] Referring to Figure 2, Figure 3, 2-1 is a positioning pin, 2-2 is a rivet hole, and 2-3 is a through hole. Referring to Figure 4, Figure 5, 5-1 is a positioning hole, 5-2 is a guide block, 5_3 is a countersunk screw hole, and 5_4 is a vacant hole.
The spring washer usually includes a washer body and a raised claw head punched and formed on the washer body. The spring washer is often placed between the bolt head of the bolt and the connected parts, wherein the raised claw head is connected to the part to be connected. The surfaces of the connecting parts are in contact, and the plane on the gasket body, opposite to the lifting direction of the raised claw head, is in contact with the bolt head. After the bolt head is tightened, the elastic reaction force generated by the raised claw head after flattening makes the The screwed threads are pressed tightly, and at the same time, the raised claw head is pressed against the bolt head and the supporting surface of the connected parts, which has the effect of preventing loosening. However, the traditional spring washer is a single-claw type. When tightening, the raised claw head will cause great damage to the surface of the connected parts, so it is not suitable for the anti-loosening treatment of parts with small surface hardness.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: carbon steel cylindrical pins, blue and white zinc pressure riveting parts pressure riveting round nuts, GB/T923 cap nuts, pressure riveting screws and other products, we We can provide you with the right fastener solution for you.
