Service HotlineThe electroplating of cross recessed screws generally refers to the electroplating of iron cross recessed screws. Stainless steel cross recessed screws are rarely electroplated. The electroplating colors of cross recessed screws are divided into environmental protection and non-environmental protection. Environmental protection blue zinc, environmental protection color zinc, environmental protection black zinc, environmental protection white nickel, etc., non-environmental protection includes white nickel, white zinc, color zinc, black zinc, black nickel, black cladding, blue zinc.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bayonet which is a T-shaped cylindrical pin with a misaligned through hole at the head, and a bayonet spring which is a ring-shaped spring steel wire whose ends are staggered. The retaining ring is clamped by the bayonet pin to fix the stop sleeve and the pin shaft together. A hydraulic excavator pin stopper with high disassembly and assembly efficiency and no need for a wrench. The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is such that it includes a latch, a stop sleeve, a pin, a bayonet, and a circlip. The staggered end is clamped into the misaligned through hole of the plug, and screwed on the bottom of the stopper sleeve to fix the stopper sleeve and the pin shaft together. The latch is composed of a bayonet pin and a circlip, the circlip is screwed around the through hole of the bayonet pin to the root of the bayonet pin, and the stopper sleeve is tightly wrapped around the pin shaft, and the circlip is tightly against the bayonet pin. The head of the bayonet pin has two T-shaped cylindrical pins with staggered through holes, and the circlip is an annular spring steel wire whose ends are staggered. By adopting the pin shaft stopping method of the above technical scheme, it is extremely convenient and quick to disassemble and assemble the pin shaft. The bolt of Guangdong Yueluo Hardware Industry Co., Ltd. is only composed of a T-shaped cylindrical pin with two staggered through holes in the head and a ring-shaped spring steel wire with staggered ends. The structure is simple, convenient to manufacture, low cost and obvious. It is an excavator pin stop method with high disassembly and assembly efficiency, no need for a wrench and low manufacturing cost.
With the rapid development of China's machinery industry, especially the development of heavy industry, the demand for large-scale metal processing equipment is increasing; at the same time, higher requirements are also placed on the technical parameters of the equipment. For some large-scale CNC equipment, to ensure the machining accuracy of the whole product, it is not only necessary to rely on high-performance components such as full closed-loop control and precision transmission components, but also requires the positioning and stability of the joint surfaces between the large and medium-sized components of the equipment. The common positioning of the joint surface between large components adopts flat key positioning, and this method requires processing the keyway at the joint surface of the large components. Since the joint surface of large parts is affected by factors such as processing and splicing, it cannot guarantee that the keyways on the large parts combined can be matched according to the theoretical requirements. Therefore, the positioning flat key needs to press the flat key in the two parts of large parts. Different repair allowances Trim into a stepped shape. The height difference of this keyway in different large components makes a single flat key need to be repaired on four sides, which increases the difficulty of the key repair process and makes it difficult to improve work efficiency. Not only that, when the flat key is repaired and assembled, it must be in an interference fit with the keyway, which makes the disassembly and assembly of the flat key more laborious.
The existing combination screws and accessories are individually processed and then handed over to the customer for assembly. This method is prone to assembly problems, and the combination screws and accessories need to be marked with identification marks, which increases the production cost.
Please refer to FIG. 1 , which is a cross-sectional view of a conventional screw and screw washer for locking two metal parts. The screw 100 is combined with the screw washer 110 to lock the metal parts 120 and 130 . The screw washer 110 includes a washer portion 112 and a body washer portion 114 . The washer portion 112 is used for electrically isolating the screw head 102 from the metal piece 120 , and the screw body washer portion 114 is used for electrically isolating the screw body 104 and the metal piece 120 . Therefore, through the design of the screw washer 110 , the screw 100 can be isolated from conducting the metal parts 120 and 130 .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: inner card gaskets, A-grade carbon steel galvanized screws, 4.8-grade rivets, industrial nuts and other products, we can provide you with suitable products for you. Fastener Solutions.
