Service HotlineThe cylindrical pin magnetic positioning automatic press-in mechanism includes a base, a guide block is arranged on the base, one end of the guide block is provided with a guide vertical plate, and a push-up column is arranged under the end, and the push-up column is connected with a driving mechanism to drive The mechanism is arranged inside the guide vertical plate; one side of the guide block is provided with a push plate, the end of the push plate is provided with a semicircular groove, the push plate is connected to the driving mechanism, and the driving mechanism is arranged on the base The other side of the guide block is provided with a workbench located on the base, an error-proof positioning mechanism is arranged above the workbench, a press-in mechanism is arranged above the error-proof positioning mechanism, and one side of the error-proof positioning mechanism is provided. There is an error-proof detection mechanism; the press-in mechanism includes a punch, a punch block and an upper template arranged in sequence from bottom to top, and the upper template is driven and connected with five driving mechanisms; the error-proof detection mechanism includes a fixed angle plate, a fixed angle The plate is arranged on the worktable, and the fixed angle plate is provided with a four-drive mechanism, and the four-drive mechanism is connected to the detection head.
There are many types of rivets, including dome head, flat head, blind rivet and so on. When riveting parts, they will have uneven force and affect the quality of riveting. Some rivet caps are too thin to easily affect the quality of riveting. Some rivets have poor tightness of riveted parts when riveting. Therefore, both the structure of the rivet and the tightness of the riveting need to be considered, so as to enhance the quality of the rivet fastening.
The existing structure is found in the practical application experience that there are still the following problems and drawbacks: the screw structure and the screw space are combined with each other in a complementary manner, so they can provide a higher torque value, however, not every workpiece. The combination requires a high torque value, so it often results in excess quality. Although the price of the screw is low, if it can change the unchanging structure of the traditional screw, it can provide a technical means to simplify (change) the process. The effect of improving production capacity and convenience of use is indeed a technical bottleneck that the relevant industry should break through.
Blind rivets are a type of rivets for single-sided riveting, but they must be riveted with a special tool - a rivet gun (manual, electric, pneumatic). This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets (which must be riveted from both sides), so it is widely used in construction, automobiles, ships, aircraft, machinery, electrical appliances, furniture and other products. Among them, the open type oblate head blind rivets are the most widely used, the countersunk head blind rivets are suitable for riveting occasions that require smooth performance, and the closed blind rivets are suitable for riveting occasions that require higher load and certain sealing performance.
Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 4 the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal cap nuts, square spot welding nuts, 201 stainless steel lock nuts, copper inlaid nuts and other products, we can provide you with suitable products for you Fastener Solutions.
