Service HotlineFor common screw belts, please refer to the Central Taiwan Announcement No. 327449 on February 21, 1998, Screw Belts (2), which includes a main body with multiple grooves on the side of the main body for the purpose of locking screw tools to drive the belt. A toggler; and a plurality of nail grooves are arranged on the nail belt so that the screw planting is arranged in an arrangement, and the nail grooves are all provided with through holes, and the through holes extend downward with a ring to form a support portion for the screws; and the It is surrounded and provided with a plurality of cutting grooves, which is beneficial for the screw to be rotated through the nail groove; and it is characterized in that the nail groove is located on the inner wall surface of the surrounding and is provided with a plurality of lobes, and these lobes are implanted in the screw. In the nail groove, the leaflet supports the screw, so that the screws with different outer diameters are fully supported and positioned by the leaflet; and/or the upper part of the leaflet is inclined or curved, so that a depression is formed above the ring to support the screw The arc surface or tapered surface of the neck can make the screw more stable to be supported.
The self-tapping locking screw is a series of coarse thread and ordinary thread, and the thread size is M3~M12mm. The threaded rod of the self-tapping locking screw is a thread with an arc-shaped triangular section. The screw is surface hardened and can be screwed into a prefabricated hole of black or non-ferrous metal material (which can be made by drilling, punching or die casting), and extruded to form an internal thread. The threaded rod portion can be made into a cylindrical or triangular shape with a diameter equal to or less than the circumscribed circle. Self-tapping locking screws have low screw-in torque and high locking performance. The varieties of self-tapping locking screws in the product standard of Chinese commodity fasteners include GB/T6560 (cross-recessed pan head), GB/T6561 (cross-recessed countersunk head), GB/T6562 (cross-recessed half-sunk head), GB/T6563 ( Hexagon head), GB/T6564 (hexagonal flower-shaped cylindrical head) five series. Self-tapping locking screws are generally fastened with pneumatic or electric screwdrivers. Most of the automotive industry uses hexagonal head, cross recessed pan head and hexagonal socket head self-tapping locking screw with high fastening efficiency.
Materials and main equipment: 1.1 Bolts, nuts and washers shall be accompanied by quality certificates and shall comply with design requirements and national standards. 1.2 The high-strength bolts should be stored in categories according to their specifications, and should be protected from rain and moisture. Do not use if the bolts and nuts are not matched and the threads are damaged. If the bolts, nuts and washers are corroded, the tightening axial force should be sampled and used only after meeting the requirements. Bolts, etc. shall not be contaminated by soil or oil, and shall be kept clean and dry. It must be used in the same batch according to the batch number, and must not be mixed or mixed. 1.3 Main tools: electric torque wrench and controller, manual torque wrench, manual wrench, wire brush, tool bag, etc. 2 Operating conditions: 2.1 Friction surface treatment: The friction surface is treated by sandblasting, grinding wheel grinding and other methods, and the friction coefficient should meet the design requirements (a requirement is that the Q235 steel is above 0.45, and the 16 manganese steel is above 0.55). The friction surface wood is allowed to have residual iron oxide scale. The treated friction surface can generate red rust surface and then install the bolts (generally stored in the open air for about 10d). The sandblasted friction surface can be installed without rusting. When grinding with a grinding wheel, the grinding range is not less than 4 times the diameter of the bolt, the grinding direction is perpendicular to the direction of force, and the friction surface after grinding should be free of obvious unevenness. The friction surface should be prevented from being polluted by oil or paint. If polluted, it should be cleaned thoroughly. 2.2 Check the hole size of the bolt hole, the burrs on the edge of the hole must be removed. 2.3 The bolts, nuts and washers of the same batch number and specification should be packaged for use. 2.4 Electric wrenches and manual wrenches should be calibrated.
Pins are frequently used parts in the machinery industry, especially in the mold manufacturing industry. With the development of the mold industry, the precision of mold manufacturing and assembly is getting higher and higher, and people are increasingly pursuing high-quality and close molds. Every detail on the mold is constantly improving, and the high-frequency use of the pins forces people to find a safer, simpler and more reliable way to disassemble and assemble.
The circlip travel mechanism includes a travel cylinder and a travel plate connected with the push rod of the travel cylinder; the travel air cylinder can control the travel plate to be inserted into the circlip press-out and positioning mechanism, and the circlip lifting and tightening mechanism; the travel plate The surface of the device is provided with a groove for placing the circlip; the height of the groove is the height of one circlip.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: dispensing screws, GB819 screws, wing bolts, natural color plastic insulating washers and other products, we can provide you with suitable fastener solutions for you .
