Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (10), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the deformation. effect.
When the iron pot is manufactured, the iron head is connected to the iron pot body through rivets, and then the pot handle is set through the iron head, and the iron head connects the pot handle and the iron pot body together. However, when the iron head is installed, the position may be inaccurate. At this time, it is necessary to remove the rivet and reinstall the iron head. At present, the removal of rivets is completely done manually, that is, workers use screwdrivers to unscrew the rivets, which is difficult to remove, wastes a lot of manpower, and has low work efficiency, thereby reducing production efficiency.
When the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
(1) Galvanized (blue-white, multicolored, black) 1. Pretreatment: thermal degreasing tank (5 tanks) - electrolytic degreasing tank (3 tanks) - rust removal tank (4 tanks) 2. Electroplating: electroplating tank (20 tank) (ammonium chloride, zinc oxide, gloss, softener solution). 3. Post-treatment: Melting tank (1 tank) - Green medicine tank (1 tank) - (blue-white/multicolored/black) (2), blackening: 1. Pre-treatment: thermal degreasing tank (4 tanks) - rust removal Tank (4 tanks) 2. Blackening: blackening (5 tanks) (flake alkali, sodium nitrite solution) 3. Post-treatment: anti-rust oil (1 tank) (3), phosphating: 1. Pre-treatment: heat Degreasing tank (1 tank) - Derusting tank (1 tank) - Electrolytic degreasing tank (1 tank), - Surface treatment (1 tank) 2. Phosphating: Phosphating (forming a film) 3. Post-treatment: dipping in anti-rust oil (2 tanks) (4) Hot dip galvanizing: 1. Pretreatment: degreasing tank (1 tank) - rust removal tank (1 tank) - FLUX tank (1 tank) - drying 2. Hot dip galvanizing: hot Zinc immersion tank 3. Post-processing: centrifugal treatment - ammonia chloride cooling - water cooling
Moisture-proof measures Iron screws are easy to rust in a humid environment. In order to prevent the screws from rusting, the screws need to be moisture-proof and moisture-proof. The moisture-proof and moisture-proof methods of screws are as follows: (1) Vibration machinery, try to use solvent-free paint. (2) It is best to use impregnating paints that do not contain oxidative components, such as epoxy-urethane (Epoxy-urethane)-based or unmodified epoxy-based (Epoxy-)-based impregnating paints. (3) When using melamine alkyd impregnating paint, the curing temperature and curing time should be adjusted. The curing temperature should be slightly higher than 130 °C (such as 135 °C) and the curing time should be longer than 180min, and the process must be strictly implemented, especially In the hot and humid season, the drying (curing) time of the paint specified in the paint factory's samples is not necessarily sufficient from the perspective of rust prevention, and the motor has a specific inner shape. (4), use paint without volatile acid. (5) Choose paint with good hydrolysis resistance.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: three-combination screws and bolts, half-threaded screw nuts, half-countersunk screws, black 12.9-grade screws and other products, we can provide you with suitable products for you Fastener Solutions.
