Service HotlineIn the prior art, the independent pocketed spring is to encapsulate the springs in bags independently, connect each independent pocketed spring side by side, and then cover it with a large non-woven fabric to form a Spring cushions. This spring mat structure has many disadvantages: 1. Uneven force and low hardness; 2. Easy to deform, pit, low flatness and unsightly; 3. The spring directly contacts the non-woven fabric, causing wear and tear, and the life of the spring mat relatively short.
Wood screws, one of which is a polished rod, the angle and pitch of the teeth of the wood screws and self-tapping are different. Self-tapping screws have high hardness, wide thread spacing, deep threads, and uneven surface, while wood screws are the opposite. Another difference is more obvious. Wood screws have no threads at the rear. Self-tapping screws are generally subject to heat treatment, and wood screws are not required. The concept of self-tapping screws is actually very general, because there are many kinds of them according to different head types. Use of wood screws: Similar to machine screws, but the thread on the screw is a special rib for wood screws, which can be directly screwed into wooden components (or parts).
Guangdong Yueluo Hardware Industry Co., Ltd. provides a nut provided by Yueluo, which includes an internal thread. is an arc curve. Compared with the nut of the same type, the normal pressure and friction force of the nut are increased, the thread is not easy to loosen, and the bolt and nut are in surface contact, so it is not easy to cause stress concentration and local material yield, which effectively improves the tightening force of the bolt and nut. Stability, increase fastening reliability.
flat washer is also called a flat washer. It is mainly stamped out of an iron plate. The shape is generally a flat washer with a hole in the middle. The size of this hole is generally determined according to customer requirements. There are 9 standards for flat washers in my country. From 2000 to 2002, GB/T97.3-2000, GB/T5286-2001, GB/T95-2002, GB/T96.1-2002, GB/T96.2 were approved and released respectively. -2002, GB/T97.1-2002, GB/T97.2-2002, GB/T97.4-2002 and GB/T5287-2002 Standard for flat washers. According to the performance grade of the flat washer, the author recommends the use of materials: ST12, ST13, Q235, Q215, Q195, etc. can be selected for the 100HV grade, and the surface hardness can reach about 110HV; 08F, 08Al, 10, 10F, etc. can be selected for the 140HV grade etc., the surface hardness can reach about 140HV; for 200HV and 300HV grades, 45, 50, 60, 70 or 65Mn steel should be selected, which can be quenched and tempered by heat treatment to meet the technical requirements of 200~300HV and 300~400HV. Because according to the standard, flat washers of 100HV and 140HV grades can be manufactured from mild steel. Most enterprises use Baosteel materials when selecting materials, which is convenient for cold stamping. The following is a brief description of Baosteel's standards. Compared with the BZJ407-1999 standard, there are major changes in Continuous Cold Rolled Low-Carbon Steel Plates and Strips and the enterprise standard: (1) The grades have been revised and integrated, and the grades have been changed from 8 commonly used to 5. St12 is changed to DC01; ST13 is changed to DC03; St14, St15 is changed to DC04; BSC2 is changed to DC05; St16, St14-T, BSC3 is changed to DC06. (2) The surface quality level is changed from two to three: the higher-level finishing surface (FB), the surface is allowed to have a small amount of defects that do not affect the formability and coating and plating adhesion, such as slight scratches, indentations, Pock, roll printing and oxidation color, etc. Premium Finished Surface (FC) products have no visible defects on the better of the two sides and must meet at least FB requirements on the other side. The super-advanced finishing (FD) product must not have any defects on the better side of the two sides, that is, it cannot affect the appearance quality after painting or the appearance quality after electroplating, and the other side must at least meet the requirements of FB. (3) The surface structure is modified from four to two, and the control value of surface roughness is increased. The average roughness Ra when the surface structure is pitted (D) is 0.6 μm. (4) The provisions on Si and residual elements in the chemical composition of the five grades have been cancelled, and the contents of elements such as C, S, and Alt have been revised.
Before the special vehicle is refitted, the chassis and the car frame should be reinforced again, and the fastened part of the rivets should be disassembled before the car frame is reinforced.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: slotted screws, multi-specification can be customized, butt-locking screws, copper countersunk head rivets, extended hook-shaped hook screws and other products, we can provide You have the right fastener solution for you.
