Service HotlineIn the switchgear of high and low voltage power equipment, the surface of many switchgear shells is painted or sprayed with plastic, and the installation beams and other parts of the switchgear and the entire cabinet must be continuously grounded according to the requirements of switchgear standards to improve the safe use of equipment. Because the common screw, spring washer, flat washer and nut type structural connection between the surface of the shell and the metal mounting beam cannot meet the requirements of grounding continuity, in order to meet the requirements, the surface of the shell is painted or Before spraying, special grounding studs must be welded. With the increase of installation beams, the number of welded studs must also increase, which increases the complexity of the product processing technology, wastes man-hours and increases costs.
Many standoffs are used in sheet metal and aluminum profile processing. However, the existing pressure riveting nut column generally adopts a clearance fit between the pressure riveting and the pressed plate, which has no effect on the general pressure riveting, but it has high surface quality requirements for aluminum profiles, especially Painting aluminum profiles will have a certain impact. First, because the bottom holes of pressure riveting on aluminum profiles are generally processed on ordinary punching machines, a tapered hole with a horn will be generated, which will further increase the gap between the pressure riveting nut columns. Make the mutual tightening force smaller, causing some aluminum profile components to loosen the riveting nut when installing screws, resulting in unqualified surface quality. Therefore, we urgently need a way to reduce the matching gap with the bottom hole of the aluminum profile pressure riveting. The pressure riveting standoff is used to increase the wrapping force between the pressure riveting standoff and the aluminum profile hole.
Half round head rivets are mainly used for riveting occasions with large lateral loads, and are the most widely used. Flat cone head rivets are often used in riveting occasions with strong corrosion such as ship hulls, boiler water tanks, etc. Countersunk head and 1200 countersunk head rivets are mainly used for riveting occasions where the surface must be smooth and the load is not large. Half countersunk head and 1200 half countersunk head rivets are mainly used for riveting occasions where the surface must be smooth and the load is not large. Flat head rivets are used for riveting occasions with general load. Flat head and flat head rivets are mainly used for riveting of metal sheets or non-metallic materials such as leather, canvas and wood. Large flat head rivets are mainly used for riveting of non-metallic materials. Semi-hollow rivets are mainly used for riveting occasions with small loads. Headless rivets are mainly used for riveting of non-metallic materials. Hollow rivets are light in weight and weak in head, and are used for riveting of non-metallic materials with small loads. Tubular rivets are used for riveting of non-metallic materials without load. Nameplate rivets are mainly used for riveting nameplates on machines and equipment.
Gaskets are divided into: flat washer - grade C, large washer - grade A and C, extra large washer - grade C, small washer - grade A, flat washer - grade A, flat washer - chamfer type - Grade A, high-strength washers for steel structure, spherical washers, cone washers, square bevel washers for I-beam, square bevel washers for channel steel, standard spring washers, light spring washers, heavy spring washers, internal tooth lock washers , Internal serrated lock washers, external serrated lock washers, external serrated lock washers, single-ear stop washers, double-ear stop washers, outer tongue stop washers and stop washers for round nuts, etc.
In the riveting operation, the rivet used is composed of a mandrel and a deformed collar. When in use, a through hole is drilled on the two components to be connected, and then the head of the rivet is passed through the through hole and clamped by a rivet. The tail of the rivet will break the rivet, the head of the rivet and the deformed collar remain in the through hole, and the whole riveting process is completed. The existing pull rivets have the following shortcomings: first, the parts where the pull rivet and the two components are connected cannot be completely and tightly fitted, which meets the requirements of non-sealing for parts that have waterproof and leak-proof requirements; second, the existing pull rivets The separation groove of the rivet mandrel is close to its head. When the mandrel is broken by the rivet during the riveting process, basically only the head of the mandrel remains in the deformation collar, and the connection of the two components depends on the deformation of the collar. Under the action of compressive stress, the inside of the deformed collar becomes hollow due to the breaking of the mandrel, and cannot bear large shear stress.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: full hollow rivets, PC board spacer studs, furniture wood products, rubber coupling gaskets and other products, we can provide you with suitable products for you. Fastener Solutions.
