Service HotlineGuangdong Yueluo Hardware Industry Co., Ltd. discloses an eccentric special-shaped rivet, which has a simple structure and is inexpensive to manufacture. The eccentric shaped rivet includes a cylindrical head and an eccentric polished rod. The diameter of the cylindrical head is larger than that of the eccentric polished rod. The eccentric polished rod is arranged at the lower end of the cylindrical head, and the axis of the eccentric polished rod is not the same as the axis of the cylindrical head. on the same straight line. The eccentric special-shaped rivet has low manufacturing cost and is easy to realize automatic assembly.
Materials and main equipment: 1.1 Bolts, nuts and washers shall be accompanied by quality certificates and shall comply with design requirements and national standards. 1.2 The high-strength bolts should be stored in categories according to their specifications, and should be protected from rain and moisture. Do not use if the bolts and nuts are not matched and the threads are damaged. If the bolts, nuts and washers are corroded, the tightening axial force should be sampled and used only after meeting the requirements. Bolts, etc. shall not be contaminated by soil or oil, and shall be kept clean and dry. It must be used in the same batch according to the batch number, and must not be mixed or mixed. 1.3 Main tools: electric torque wrench and controller, manual torque wrench, manual wrench, wire brush, tool bag, etc. 2 Operating conditions: 2.1 Friction surface treatment: The friction surface is treated by sandblasting, grinding wheel grinding and other methods, and the friction coefficient should meet the design requirements (a requirement is that the Q235 steel is above 0.45, and the 16 manganese steel is above 0.55). The friction surface wood is allowed to have residual iron oxide scale. The treated friction surface can generate red rust surface and then install the bolts (generally stored in the open air for about 10d). The sandblasted friction surface can be installed without rusting. When grinding with a grinding wheel, the grinding range is not less than 4 times the diameter of the bolt, the grinding direction is perpendicular to the direction of force, and the friction surface after grinding should be free of obvious unevenness. The friction surface should be prevented from being polluted by oil or paint. If polluted, it should be cleaned thoroughly. 2.2 Check the hole size of the bolt hole, the burrs on the edge of the hole must be removed. 2.3 The bolts, nuts and washers of the same batch number and specification should be packaged for use. 2.4 Electric wrenches and manual wrenches should be calibrated.
Bolt: A mechanical part, a cylindrical threaded fastener with a nut. A type of fastener consisting of a head and a screw (a cylinder with an external thread), which needs to be matched with a nut to fasten and connect two parts with through holes. This form of connection is called a bolted connection. If the nut is unscrewed from the bolt, the two parts can be separated, so the bolt connection is a detachable connection.
With the rapid development of China's machinery industry, especially the development of heavy industry, the demand for large-scale metal processing equipment is increasing; at the same time, higher requirements are also placed on the technical parameters of the equipment. For some large-scale CNC equipment, to ensure the machining accuracy of the whole product, it is not only necessary to rely on high-performance components such as full closed-loop control and precision transmission components, but also requires the positioning and stability of the joint surfaces between the large and medium-sized components of the equipment. The common positioning of the joint surface between large components adopts flat key positioning, and this method requires processing the keyway at the joint surface of the large components. Since the joint surface of large parts is affected by factors such as processing and splicing, it cannot guarantee that the keyways on the large parts combined can be matched according to the theoretical requirements. Therefore, the positioning flat key needs to press the flat key in the two parts of large parts. Different repair allowances Trim into a stepped shape. The height difference of this keyway in different large components makes a single flat key need to be repaired on four sides, which increases the difficulty of the key repair process and makes it difficult to improve work efficiency. Not only that, when the flat key is repaired and assembled, it must be in an interference fit with the keyway, which makes the disassembly and assembly of the flat key more laborious.
The traditional gasket is a single-piece gasket that works independently. This gasket mainly relies on friction to achieve the anti-loosening effect. The new washer is composed of two pieces. Its unique embedded structure changes the way that the traditional washer mainly achieves anti-loosening through friction. Instead, it adopts the most advanced anti-loosening technology in the world and uses the tension between the two gaskets to achieve. The dual effect of anti-loosening and tightening.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: accessories screws, GB5789 screws, rubber plug expansion bolts, iron-plated color galvanized screws and other products, we can provide you with suitable fasteners for you solution.
