Service HotlineThe blind rivet is realized by pulling the core head. With the help of a force from the inside to the outside, under the action of the unidirectional pulling force, the pulling screw is pulled upwards, which causes the outer collar material to expand and deform, resulting in a sexual tightening force. , After the riveting is completed, the tension screw in the middle part breaks and falls out. Since a large pulling force is required to cause the rivet to expand and deform, the tensile screw is longer and accounts for about 60-80% of the total length of the rivet. At the same time, due to the limitation of the deformation mode, it is difficult for the blind rivet to be made into a hexagonal structure like a rivet nut, so the torsion resistance of its connection is low.
Some heavy equipment such as large motors, large reducers, etc., in order to facilitate the installation and adjustment of equipment and the need for maintenance space, a certain position needs to be moved during equipment installation and maintenance. Usually, a steel base or platform is set under the equipment, and the base or The platform is provided with an oblong bolt installation slot, commonly known as an oblong slot, as shown in Figure 1--Figure 4. When using common hexagon head bolts or common T-bolts with the long circular groove in Figures 1 and 2, auxiliary fixing bolts or welding stoppers are required on the back of the long circular groove to prevent the bolt from rotating when the nut is tightened. In Fig. 3 and Fig. 4, the long circular groove itself has a clamping groove to prevent the rotation of the bolt, but this structure greatly increases the processing cost of the long circular groove.
The main function of the spring washer is to prevent the nut from loosening. It is also known that: the existing spring washer is a ring made of spring steel, and then a gap is cut in the diameter direction on the ring, and the heads on both sides of the gap are cut. The material of the part is turned to two different sides of the ring to form a pawl, and the purpose of preventing loosening is achieved by the fit between the pawl and the nut on the surface and the workpiece. Obviously, only one pawl is used to achieve the purpose of preventing loosening. Since the braking force generated by one pawl is limited, there are defects of poor braking effect and poor anti-loosening effect.
The retaining ring is a ring-shaped component fastened on the shaft and the inner hole. Its main function is to prevent other components installed on the shaft and the inner hole from sliding axially on the shaft. It is a fixed standard part.
China is the world's largest producer of carbon steel fasteners such as screws, nuts and bolts, and the EU is a major market for these products. In January 2009, the EU decided to impose anti-dumping duties of 26.5% to 85% on Chinese carbon steel fastener products. On July 31 of the same year, China resorted to the relevant EU legislation and anti-dumping measures to the WTO dispute settlement mechanism. The case became China's first lawsuit against the EU at the WTO. On July 15, 2011, the WTO Appellate Body issued a report and finally ruled that China won the case in the trade dispute with the European Union on fasteners. The head of the Department of Treaty and Law of the Ministry of Commerce of China welcomed the ruling on the 16th, and said that China's victory in the case is of great significance, which will help improve the competitive environment for Chinese companies in the international market including the European Union, and will also strengthen the WTO members' interest in the case. Confidence in WTO rules and the multilateral trading system. This is not only a victory for China's industry, but also a victory for WTO rules, the official said. The WTO Appellate Body found in its ruling report issued on the 15th that Article 9(5) of the EU's Basic Anti-dumping Regulations on individual tax rates violated WTO rules; at the same time, the Appellate Body overturned some of the panel's rulings and supported China's position , ruled that the EU's anti-dumping measures against Chinese screws, nuts, bolts and other carbon steel fasteners also violated WTO rules in terms of domestic industry identification, normal value and fair comparison of export prices. The head of the Treaty and Law Department of the Ministry of Commerce of China said that the EU is one of the WTO members that has initiated the most anti-dumping investigations against Chinese products in the world. unfair treatment. He said that China hopes that the EU will cancel the legislation and discriminatory anti-dumping measures that are inconsistent with WTO rules as soon as possible, treat Chinese export enterprises fairly, and effectively safeguard free trade and fair competition.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: blue and white plated spring washers, pin positioning, column knurled stud nut column, GB5873 external hexagon bolts and other products, we can provide you with suitable products Your fastener solution.
