Service HotlineIn order to achieve the above purpose, Yueluo provides the following technical solutions: threaded rivets include a nail rod, an expansion piece, and a nail sleeve, one end of the nail rod is provided with a mounting piece, and the side of the mounting piece away from the nail rod is movably installed with a mounting piece. There is a driving mechanism. The driving mechanism includes a mounting cylinder and a movable rod. A cross groove is formed at one end of the mounting piece close to the driving mechanism. The rod is movably installed on the inner side of the installation cylinder, and one end of the movable rod close to the cross groove is fixedly provided with a cross connecting piece that matches the cross groove, the cross connecting piece is matched with the cross groove, and the movable rod is far away from the cross groove. One end of the cross connecting piece is fixedly provided with a fixing piece, the fixing piece and the installation cylinder are screwed together by threads, the expansion piece is sleeved on the outer side of the nail rod, and the nail sleeve is movably installed on the nail rod away from the driving mechanism The outer side of one end of the nail rod is movably installed with a fixing mechanism.
Usually, the pumped storage unit adjusts the opening of the guide vane through the movable guide vane to control the power generation output and the pumping head of the unit. The torque of the guide vane rotation depends on the relay to act on the control ring, and the torque is transmitted to the guide vane rotating shaft through the connecting rod and the arm. The torque transmission between the crank arm and the rotating shaft all acts on the pin located between them. When the unit is overhauled, it is necessary to remove the pin between the arm and the rotating shaft of the guide vane in advance when it comes to the replacement of the guide vane. However, due to the special position of the pin and the limited inspection space, the conventional method is not only time-consuming and laborious, but also has the risk of damaging the pin. Maintenance work brings inconvenience.
The existing way to achieve radial locking of the shaft is generally to sleeve the positioning block on the shaft, and then use a cylindrical pin to pass through the positioning block to lock the shaft. The locking structure and method are as follows: A locking groove with an arc-shaped cross-section is set on the outer side of the shaft along the direction perpendicular to the axis of the shaft, an opening is set on the positioning block, and then a cylindrical pin is used to pass through the positioning block from the outside of the positioning block and screw the lock at one end of the cylindrical pin. When the lock nut is tightened, the opening on the positioning block will be deformed inwardly and locked on the shaft.
At present, due to the installation position determined in the design process of the traditional thrust cylinder in China, the corresponding position of the piston rod and the clamping arm is fixed, and it is impossible to ensure that the workpiece can be clamped while the workpiece is thin. It is not conducive to the use of such products when clamping. Secondly, when the workpiece is assembled or welded, it not only needs to be tightened in a certain direction, but also needs to be positioned, so as to ensure the accuracy required for processing. When a workpiece is fixed in this way, it must be realized by adding a mechanism, which will increase the complexity of the system and bring inconvenience to installation and maintenance.
At present, during assembly of many pin installation mechanisms, the pins need to be installed into the holes or arranged in an orderly manner, and there are many problems in this assembly method. First of all, during assembly, if the hole diameter of the hole product is large, when the pin enters the hole of the hole product, part of the pin entering the hole of the hole product is not fixed, which often leads to slight deviation. In addition, this assembly method is usually only suitable for parts with large apertures and small depths, and when installing multiple pins, it is impossible to automatically install all pins in place due to space constraints. Special tools need to be made for installation operations, and it is easy to cause pins. damage.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal head reinforcing rod bolts, iron gasket manufacturers, high-precision stainless steel bolts, JISB1251 and other products, we can provide you with suitable fastening for you. piece solution.
