Service HotlineIn some embodiments, the rivet fixing mechanism includes a left moving block, a right moving block, a return spring and a bracket, wherein both the left moving block and the right moving block are movably mounted on the bracket, and the left moving block and the right moving block are connected by a return spring, The insertion mouth can extend between the left moving block and the right moving block, and withstand the left moving block and the right moving block. The left moving block is provided with a left half hole, and the right moving block is provided with a right half hole matching the left half hole. hole. Therefore, when the insertion nozzle is not inserted, the left moving block and the right moving block can be combined together by the return spring, so that the left half hole and the right half hole are combined into one hole to fix and position the rivet, and when the insertion nozzle is inserted When , the left moving block and the right moving block will be pushed up by the insertion mouth to separate the left half hole and the right half hole, so that the rivet is no longer fixed and can be inserted with the movement of the insertion mouth.
When using screws, if you can understand the mechanical properties of screws first, then you can use screws better. Different types of screws have different mechanical properties, and the different mechanical properties lead to different occasions when screws are used. 1. Self-tapping screws: mechanical performance requirements 1. Heart hardness: standard value HRC28-38. When testing, take the section 1-2 times the diameter of the name from the tail. If the length of the name is too short, it can be embedded first, and then the hardness is measured. 2. Surface hardness: standard MIN HV450. 3. Carburized layer: standard 4#-6#: 0.05-0.18mm, 8#-12#: 0.10-0.23 mm, 14#: 0.13-0.28 mm. The main purpose of carburizing is to enhance the surface hardness and ensure the strength of the teeth. If the decarburization is too deep and the carburization is insufficient, the strength of the teeth will not meet the requirements, that is, the teeth will be damaged during the screw-in test. 4. Torque: standard specification 4#5#6#7#8#10#12#14#A tooth 14212835455696145AB tooth 142128354565102165. 5. Screw-in test: screw the self-tapping screw into a steel plate with a reserved test hole. The self-tapping screw should form a matching thread in the test plate, and the thread of the screw itself will not be deformed or damaged until the end. Tapered threads pass completely through the test plate. The screw-in test is only applicable to AB, B, BP and other types of self-tapping screws. It is stipulated in IFI that the test plate shall be prepared from semi-hard low-carbon cold-rolled steel, and the hardness of the steel plate is 70–85HRB in Rockwell. The standard specification of the steel plate, that is, the thickness, is shown in the table below. The test hole should be punched or drilled, and the tolerance is the specified nominal diameter (see the table below) ± 0.025mm. Specifications 6#7#8#10#12#1/4 Test plate thickness (mm) 1.85-1.953.12-3.234.68-4.84 Aperture (mm) ±0.0252.953.263.454.044.765.50.
The use of stainless steel screw lines: The hardness of stainless steel screw lines causes them to have different uses. Generally, they are used as small screws in life, but also as car screws and compression screws. They are widely used in normal life. Types of stainless steel screw lines: In appearance, screw lines are generally divided into fog surface spring lines and bright surface screw lines. The hardness of matte surface screw lines is higher than that of bright surface screw lines. For products with low appearance requirements and relatively high elasticity requirements. Paper, oxalic acid, fertilizer and other production equipment; photography, food industry, facilities in coastal areas, ropes, CD rods, bolts, nuts.
In view of the deficiencies of the prior art, a simple structure is provided, which can ensure that the nut body and the washer are assembled together during the production of the wheel nut, and will not be separated from each other in any occasion, so as to ensure the reliability of the assembly, and the nut will no longer appear. The wheel nut assembly that needs to be reassembled after use or placement saves time and effectively improves the convenience of the wheel nut when it is used or placed
In industrial production, some products need to remove the fixing screws; or in the assembly line, the screws that fix the product on the fixture also need to be removed when the product is unloaded. At present, the dismantling of the screws is mainly completed by the manual operation of the operator. However, this method of manually dismantling the screws has low work efficiency and high production cost.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: toothed lock nuts, U-shaped clamp screws, nut combination sets, locking non-slip toothed hexagon screws and other products, we can provide you with The right fastener solution for you.
