Service HotlineIt can be seen from the figure that no matter how the screw core swings, it will not fall off from the screw sleeve. This is because part of the bead 5 is stuck in the hole 6 of the screw sleeve 1 and the other part is stuck in the screw core 2. In the groove 8, it plays the role of positioning. If the screw sleeve rotates clockwise, the beads 5 can only slide in the groove 8 of the screw core 2 under the driving of the screw sleeve 1 and cannot drive the screw core 2 to rotate. If the screw sleeve 8 rotates in the opposite direction, the bead 5 will be stuck on the stop 7 of the screw core 2 so as to drive the screw core 2 to rotate.
In some embodiments, the rivet fixing mechanism includes a left moving block, a right moving block, a return spring and a bracket, wherein both the left moving block and the right moving block are movably mounted on the bracket, and the left moving block and the right moving block are connected by a return spring, The insertion mouth can extend between the left moving block and the right moving block, and withstand the left moving block and the right moving block. The left moving block is provided with a left half hole, and the right moving block is provided with a right half hole matching the left half hole. hole. Therefore, when the insertion nozzle is not inserted, the left moving block and the right moving block can be combined together by the return spring, so that the left half hole and the right half hole are combined into one hole to fix and position the rivet, and when the insertion nozzle is inserted When , the left moving block and the right moving block will be pushed up by the insertion mouth to separate the left half hole and the right half hole, so that the rivet is no longer fixed and can be inserted with the movement of the insertion mouth.
The paint mixing mixer used for color matching in the auto repair industry uses a multi-link connection transmission as the main driving force. The transmission of torque has higher quality requirements for the impact resistance and fatigue resistance of the cotter pin. During the use of the cotter pin, it was found that the cracking phenomenon occurred due to insufficient strength, resulting in the machine not running. In the existing multi-link transmission mode of the paint mixing mixer, the connecting rod drives more than 10 paint pots in each layer of the frame to stir, and the bottom connecting rod is also responsible for the transmission of the torque of the upper connecting rod, which leads to the connection between the connecting rod and the connecting rod. The pins connected by the rods must have strong impact resistance and fatigue resistance, and must have a certain anti-loosening function.
Type 1 nut refers to an ordinary hexagonal nut with a nominal height of m ≥ 0.8D. Its type and size should meet the requirements of GB/T6170; while the height of type 2 nut is higher than that of type 1 nut, its type and size should comply with GB/T6170. T6175. There are two purposes to increase the type 2 nut: one is to obtain a relatively inexpensive nut that does not require heat treatment by increasing the height of the nut. Because D≤M16 grade 8 type 1 nuts do not need heat treatment, among grade 8 nuts, only the specifications of D>M16~39 use type 2 nuts. Obviously, type 1 nuts that do not need heat treatment cannot reach grade 9 nuts. Mechanical property requirements. Another purpose of specifying Type 2 nuts is to obtain a more ductile grade 12 nut. As the height of the nut increases, the guaranteed stress index can be achieved at a lower quenching and tempering hardness, so the toughness of the nut is increased. Classified by tooth spacing: standard teeth, regular teeth, fine teeth, very fine teeth and cross teeth. Classification by material: stainless steel hexagon nuts and carbon steel hexagon nuts, copper hexagon nuts, iron hexagon nuts. Classification by thickness: hexagonal thick nuts and hexagonal thin nuts. Classification by usage: hot melt copper nut, hot pressed copper nut, embedded copper nut and ultrasonic copper nut
Wood screws, one of which is a polished rod, the angle and pitch of the teeth of the wood screws and self-tapping are different. Self-tapping screws have high hardness, wide thread spacing, deep threads, and uneven surface, while wood screws are the opposite. Another difference is more obvious. Wood screws have no threads at the rear. Self-tapping screws are generally subject to heat treatment, and wood screws are not required. The concept of self-tapping screws is actually very general, because there are many kinds of them according to different head types. Use of wood screws: Similar to machine screws, but the thread on the screw is a special rib for wood screws, which can be directly screwed into wooden components (or parts).
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: multi-wave spring wave washers, GB221976 screws, small metal washers, thickened washers, furniture bolts and other products, we can provide you with The right fastener solution for you.
