Service HotlineCylindrical pins are widely used, and they are usually provided with matching pin holes. For the tails of cylindrical pins exposed outside the pin holes, they usually do not have a guiding function, which cannot meet the needs of quick installation of workpieces.
The fixing screw proposed by Guangdong Yueluo Hardware Industry Co., Ltd. has a screw body 1, and the axial surface of the screw body 1 is formed with extending screw teeth 6, and the axial surface is a column along the central axis direction of the cylinder of the screw body 1. The body surface has a hemispherical screw tail 7 at the bottom, and a screw head 2 at the top. The upper surface of the screw head 2 is provided with a slot (not shown). The screw body 1 is composed of the upper tapered rod 4 and the lower cylindrical screw 5. The tapered rod 4 is an inverted cone, the diameter of its circular upper surface and the diameter of the screw mounting hole 10. equal. The fixing screw also has a washer 3, the washer 3 is arranged between the screw head 2 and the screw body 1, the lower surface of the cylindrical washer 3 has a number of teeth 8, the teeth 8 are along the The upper surface of the inverted cone of the tapered rod 4 and the edge of the washer 3 are connected to form a straight convex strip 15 extending outward; the convex strip 15 can also be designed in an arc shape. The fixing screws for installation proposed by Guangdong Yueluo Hardware Industry Co., Ltd. can be made of metal materials in one piece. As shown in Figure 3, it is a schematic diagram of the installation of Guangdong Yueluo Hardware Industry Co., Ltd. for PCB board fixing. When installing, first pass the screw body 1 of the fixing screw through the mounting hole 10 and the copper column 11 provided on the PCB board 9, so that the tail 7 of the screw reaches the mounting hole 13 on the casing 12, and then use the tightening tool 14 to insert the screw At the notch on the top of the head, forcefully press the inverted cone design taper rod 4 of the screw body 1 into the mounting hole 10, so that the tail 7 passes through the mounting hole 13. Due to the outer diameter D at the bottom of the taper rod and the screw mounting hole The aperture size of 10 is equal, and the fixing screws are pressed and fixed, so that the PCB board 9 can be automatically corrected in the process of fixing its front, back, left and right deflections, and the accuracy of the installation position of the PCB board 9 can be ensured. As shown in Figure 4, after the fixing screw is screwed into the casing, the washer 3 is fully contacted and pressed on the PCB board 9, and the PCB board 9, the copper column 11 and the casing 12 are firmly connected together without sliding. . The teeth 8 on the washer 3 are in full contact with the surface of the PCB board 9, so that a ground wire path is set up between the PCB board 9 and the casing 13 by the metal fixing screw 1, thereby ensuring that the PCB board 9 is fully grounded , the design of the teeth 10 on the washer 3 also has a non-slip function. The fixing screws for installation designed by Guangdong Yueluo Hardware Industry Co., Ltd. make use of the cooperation, friction and electrical conductivity in the mechanical connection, which fully guarantees the firm installation of the PCB board and the chassis and the good grounding of the PCB board. Moreover, the ellipsoid tail of the fixing screw The surface is relatively smooth, even if the mounting holes are exposed, it will not cause scratches on the hands and desktop. The above is only the embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., and does not limit the scope of Guangdong Yueluo Hardware Industry Co., Ltd., any equivalent structure made by using the contents of the description and drawings of Guangdong Yueluo Hardware Industry Co., Ltd. or etc. Effective process transformation, or direct or indirect application in other related technical fields, are also included in the protection scope of Guangdong Yueluo Hardware Industry Co., Ltd.
Inspection method There are two types of screw surface inspection, one is the inspection before the screw is produced and not plated, and the other is the inspection after the screw is plated, that is to say, after the screw is hardened and the surface of the screw is treated. . After the screws are produced and before electroplating, we inspect the screws in various aspects such as size and tolerance. See if there are national standards or customer requirements. After the surface treatment of the screws, we will inspect the plated screws, mainly to check the color of the plating and whether there are any broken screws. In this way, when we deliver screw goods to customers, customers can successfully pass the customs when they receive the goods. Inspection of screws after treatment: 1. Appearance quality requirements The inspection of the appearance of screws is carried out from the aspects of appearance, electroplating layer and so on. Second, the inspection of the thickness of the screw coating 1. The measuring tool method uses a micrometer, a vernier caliper, a plug gauge, etc. 2. Magnetic method The magnetic method is used to measure the thickness of the coating layer, which is a non-destructive measurement of the non-magnetic coating layer on the magnetic substrate with a magnetic thickness gauge. 3. Microscopy Microscopy is called metallographic method, which is to magnify the etched fasteners on a metallographic microscope with a micrometer eyepiece to measure the thickness of the coating on the section. 4. Timing flow method The timing flow method uses a solution that can dissolve the coating to flow on the local surface of the coating, and calculates the thickness of the coating according to the time required for the local coating to dissolve. There are also coating drop method, anodic dissolution Coulomb method, etc. 3. Inspection of the adhesion strength of the screw coating There are many methods for evaluating the adhesion between the coating and the base metal, usually the following. 1. Friction polishing test; 2. File method test; 3. Scratch method; 4. Bending test; 5. Thermal shock test; 6. Extrusion method. 4. Inspection of corrosion resistance of screw coatings The corrosion resistance inspection methods of coatings include: atmospheric exposure test; neutral salt spray test (NSS test); acetate salt spray test (ASS test), copper accelerated acetate salt spray test (CASS) test); and corrosion paste corrosion test (CORR test) and solution spot corrosion test; immersion test, inter-dipping corrosion test, etc.
Generally, we have to divide the fine thread nut and the coarse thread nut first, but in fact, no matter what kind of fine thread, coarse thread, their specifications are the same, their specifications are M3, M4, M5, M6, M8, M10, etc. . But there is another kind of hexagonal nut, which is divided into English and American, which is only a different national standard. Made in China, it is called the national standard hexagon nut
T-bolt is a common fastener, which is mostly used where there is a T-slot on the workbench or where the connection can only be made from the side to be connected. However, it has the following problems in the actual production and processing process. 1. The T-bolt manufactured according to the current GB37-88 is used in conjunction with the T-slot on the worktable, which is easy to damage the T-slot on the worktable. 2. According to the observation and investigation, it is found that 90% of the damage to the T-bolt manufactured by GB37-88 is thread damage during use, and the T-shaped part is rarely damaged, resulting in a waste of raw materials. SUMMARY OF THE INVENTION The purpose of the present invention is to solve the problem that the current composite T-bolt is easy to damage other equipment and cause waste of raw materials in the actual use process, and to provide a simple structure, easy to use, safe and reliable, and not easy to damage other equipment. , thereby saving raw materials and other advantages of composite T-bolts. In order to achieve the above purpose, the present invention adopts the following technical scheme: a composite T-bolt, which includes a bolt, and one end of the bolt is connected with the T-shaped block cockroach. The T-shaped block is provided with a tapered hole, and the connection between the bolt and the T-shaped block is a cone, which is matched with the tapered hole. The utility model combines the two parts of the T-shaped block and the threaded bolt through the T-shaped block and the taper hole and the cone on the bolt to automatically lock the two parts before use. When the threaded part of the bolt is damaged, only the threaded bolt needs to be replaced. That's it. Compared with the domestic T-shaped bolts currently produced in the manufacturing process, the utility model solves the problems of complicated manufacturing processes and waste of raw materials. It is well known that the manufacture of T-bolts requires processing such as forging, turning, milling, and heat treatment. Since the composite T-bolt is used in combination with the T-block and the bolt, and the T-block is rarely damaged, after purchasing or manufacturing the T-block once, you only need to purchase or manufacture the bolt in the future. Compared with the T-bolts currently produced in China, the composite T-bolts can better protect the T-slots on the working surface. Because the T-bolt currently produced in China will rotate a certain angle around the axis of the T-bolt when fixing the object, the T-bolt will rotate at a certain angle, thereby reducing the contact between the T-bolt T-shaped surface and the T-slot stress surface of the working face. surface, causing stress concentration on this surface. The composite T-bolt avoids the above problems due to the increase of the guide surface, thereby protecting the T-slot. The beneficial effects of the utility model are: 1. Saving raw materials. 2. Reduce processing costs. 3. Simplify the technological process. 4. Protect the T-slot.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: butterfly bolts, extended inner and outer wire conversion braces, miniature screws, decorative/capped nuts and other products, we can provide you with suitable fasteners. Firmware Solutions.
