Service HotlineCabinets are one of the must-have furniture in home improvement homes. They are extremely useful. Various cabinets may be used in kitchens, bathrooms, bedrooms, living rooms, and even balconies. The traditional cabinets are assembled in advance and then placed in the appropriate position, which is very inconvenient to transport. Currently, the commonly used cabinets are spliced together with plates and hardware accessories. During production and transportation, the plates and hardware accessories are independent. For production, processing and transportation, after it is sent to the destination, it is assembled with the plates by screws and other hardware accessories to form the entire cabinet structure. The current cabinet installation structure usually exposes some hardware accessories such as screws on the outside or inside of the cabinet, which not only affects the overall aesthetics, but also scratches the items during use, which affects the use effect. Some designs allow a plastic fastener to be fastened on the outside of hardware accessories (mainly screws). Although it can alleviate the above problems to a certain extent, it still does not fundamentally solve the problem, and the integrity is still not good.
The produced screws, due to unreasonable production aspects, are likely to cause quality problems in the screws. During production, many screw quality problems may be found upon delivery. Let's talk about the quality problems often encountered by screws and the reasons for the quality problems, and finally put forward some solutions. 1. The head of the screw is deformed and the head is crooked. The possible reasons are the poor installation of the first punch of the screw die and the improper adjustment of the machine. 2. The head of the screw is not round. The reason is that the selection of the first punch of the screw mold is improper or the first punch is not full enough. 3. The screw has burrs or burrs. The reason is the poor forming of one punch, mainly caused by too large gap between punch and die hole or too short punch. 4. The screw head is cracked and the screw head is cracked. The reason may be that there is a problem with the quality of the screw wire itself, so before the screw wire is headed, the quality department must check it and use the potion. Especially the stainless steel screw wire, it is necessary to check that it is stainless steel 201 and that is stainless steel 304. It is also possible that a die is used incorrectly (such as a die with a hexagonal washer head for a pan head), and the viscosity of the lubricating oil fails. For the problem of the screw head, you can read the article written by Manager Zhu above - high-strength screw fracture or head crack detection. In this article, some problems encountered by the screw head and how to detect the screw head problem are clearly introduced [4]. The common quality reasons for screws are of course more than the above, this is only part of it. There are other quality issues, then Manager Zhu will talk about it. The above screw quality reasons are for reference. If you encounter these problems, you can try the solutions proposed.
Principles of stainless steel screw material selection: The selection of stainless steel materials is mainly considered from the following five aspects. 1. Requirements on mechanical properties, especially strength, of stainless steel screw materials; 2. Requirements on corrosion resistance of materials by working conditions; 3. Heat resistance of materials by working temperature (high temperature strength, oxidation resistance) 4. Requirements for material processing performance in terms of production technology; 5. Other aspects such as weight, price, procurement and many other factors must be considered.
The tooling for screw standard parts provided by Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. mainly solves the problems of low manual operation matching efficiency, wrong specifications of screw standard parts, and easy falling of screw standard parts into the product when assembling screws in the prior art. . The specific technical solutions of Guangdong Yueluo Hardware Industry Co., Ltd. are as follows. The screw standard parts supporting tooling includes a stud sleeve hole plate, a gasket sleeve hole plate and a nut sleeve hole plate with matching structure; the stud sleeve hole plate There is at least one stud hole matching with the assembled stud structure, at least one gasket hole matching with the assembled gasket structure is arranged on the gasket sleeve hole plate, and the nut sleeve hole plate is provided with at least one gasket hole matching with the assembled gasket structure. At least one nut hole matched with the assembled nut structure; the number of stud holes, gasket holes and nut holes are equal. The above-mentioned stud sleeve hole plate is provided with a positioning device, and the gasket sleeve hole plate is provided with a matching positioning hole; or the gasket sleeve hole plate is provided with a positioning device, and the stud sleeve hole plate is provided with a matching positioning hole. The above stud holes are through holes; the nut holes are blind holes. Forty to one hundred and fifty stud holes are arranged on the stud sleeve hole plate. The above-mentioned positioning device is a positioning plate and/or a positioning column. The advantage of Guangdong Yueluo Hardware Industry Co., Ltd. is that the matching tooling for screw standard parts improves the matching quality of screw standard parts, effectively prevents screw standard parts from falling into the product easily and screw specifications are wrong; it simplifies the matching difficulty of screw standard parts and improves assembly efficiency. . The screw standard parts supporting tooling can be processed differently according to different screw standard parts specifications, and the applicability is very wide.
The spring washer is designed for screw backstop, usually a single-turn cylindrical coil spring. In order to improve its backstop function, there is also an integrated spring washer. Its structure is that the inner ring of the flat washer has multiple wings. Fold into spring tabs. Another type of washer used for backstop similar to spring washers is a serrated lock washer. However, this kind of lock washer usually has a small thickness, which is formed by folding the inner ring or the outer ring of the washer on the plane. When tightening, the elastic force is small, and the second is easy to be flattened, so that the stop The retreat function is still not strong enough.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: wholesale of flat head rivet nuts, pre-embedded injection molded copper nuts, four-slot nuts and nuts, cap anti-thread anti-buckle nuts and other products, we We can provide you with the right fastener solution for you.
