Service Hotline1. The twisted screw should be considered according to the actual inner diameter of the barrel, and the outer diameter deviation of the new screw should be given according to the normal clearance with the barrel. 2. After the thread surface with the reduced diameter of the worn screw is treated, the wear-resistant tungsten carbide alloy is thermally sprayed, and then ground to size. 3. Surfacing wear-resistant tungsten carbide alloy on the thread part of the worn screw. According to the degree of screw wear, surfacing welding is 1~2mm thick, and then the screw is ground and processed to size. This wear-resistant tungsten carbide alloy is composed of materials such as C, Cr, Vi, Co, W and B, which increases the wear resistance and corrosion resistance of the screw. 4. The bottom diameter of the screw is repaired by electroplating hard chromium. Chromium is also a wear-resistant and corrosion-resistant metal, but the hard chromium layer is easier to fall off.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (10), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the deformation. effect.
Flat washers are usually thin pieces of various shapes used to reduce friction, prevent leakage, isolate, prevent loosening, or distribute pressure. Such components are found in many materials and structures to perform a variety of similar functions. Restricted by the material and process of threaded fasteners, the bearing surface of fasteners such as bolts is not large, so in order to reduce the compressive stress of the bearing surface and protect the surface of the connected parts, washers are used.
As shown in Figures 1 and 2, Yueluo is an automatic locking screw. From bottom to top, there are screw head 1 with external thread, screw rod and nut 3. The screw rod is a hollow screw rod 2, and the hollow screw There are long holes 7 on both sides of the rod 2, the width of the long hole 7 is smaller than the inner diameter of the hollow screw rod 2, and a spring 4 is arranged in the inner cavity of the hollow screw rod 2, and the spring 4 is not smaller than the hollow screw rod 2 in the free extension state. The upper end of the spring 4 is provided with a plug 5, the distance between the two wings 6 of the plug 5 is greater than the diameter of the nut 3, and the two wings 6 of the plug 5 protrude out of the hollow screw rod 2 through the long hole 7. When using the Yueluo, you only need to compress the spring through the two wings, insert the U-shaped clip after the neutral position is exposed, and then release the two wings, the spring will automatically return and compress the U-shaped clip, which is easy to use, safe and reliable. Claim 7. A self-locking screw, from bottom to top, is a screw head, a screw rod and a nut provided with an external thread, characterized in that the screw rod is a hollow screw rod, and both sides of the hollow screw rod are respectively provided with Long hole, the width of the long hole is smaller than the inner diameter of the hollow screw rod, the inner cavity of the hollow screw rod is provided with a spring, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole.
In the design of modern aviation and aerospace vehicles, in order to reduce weight and save space, the space of the fastening installation system is getting narrower and narrower, and blind hole installation is often required. In this case, single-sided riveting installation is usually used for fastening connection. At present, this kind of fastening connection products are mainly blind rivets. The riveting installation principle of blind rivets is to use the method of pulling, pulling the mandrel, and extruding the nail sleeve to deform it at the blind end to achieve the function of fastened connection. This kind of fastening connection method requires special riveting, generally imported riveting, the replacement of internal parts is expensive, the installation process is complicated, and the installation cost is high.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: enlarged bolts, color zinc 4.8 screws, hexagonal nuts, copper hollow rivets and other products, we can provide you with suitable fastener solutions for you Program.
