Service HotlineMost of the blind hole installation rivets have the characteristics of light weight, reliable connection, high strength, and convenient and quick installation. For example, blind rivets have been widely used in various aerospace vehicles.
The pretreatment process is a key process that determines the quality of nickel-phosphorus plating on high-strength bolts. The purpose of this process is to remove the passivation layer on the surface of the bolt and prevent the regeneration of the passivation film. The execution of this process directly determines the degree of bonding between the substrate and the coating. Most of the quality accidents in production are caused by poor pretreatment of bolts. Before plating, the oil, rust and oxide scale attached to the surface of the bolt must be carefully removed; the difference with electroplating is that it should be inspected more carefully, and plating is absolutely not allowed on unclean bolts. ① Inspection of bolts: Visual inspection of the surface quality of bolts requires that any burrs left by processing must be removed, and sharp edges and corners must be rounded. ② Manual degreasing; ensure that the surface of the substrate is free of oil stains. ③ Soak and remove oil; boil the bolts in alkaline water to remove the surface oil. ④ Pickling: In order to prevent the alkaline degreasing solution from contaminating the flash nickel plating tank, electro-activation treatment is carried out with pickling solution before flash nickel plating. ⑤ Electro-activation; electro-activation treatment with acid solution. ⑥ Flash nickel plating; flash nickel plating should be used for low alloy steel to increase the bonding strength between the coating and the substrate.
leak-proof combined gasket relates to a gasket and solves the problem of short service life of the existing gasket. The combined gasket comprises: an O-shaped sealing ring, which is an annular sealing ring with an outer diameter of D and an inner diameter of E. The section diameter is A; the steel outer ring is a steel flat annular outer ring, which is sleeved on the outer surface of the O-ring, the inner diameter is F, and F=D, the thickness is B, B=0.785A ;The steel inner ring is a steel flat annular inner ring, embedded in the inner surface of the O-ring, the outer diameter is G, and G=E; the thickness is C, and C=B. When the O-ring in the combined washer is pressed by the bolt for sealing, it is positioned between the steel outer ring and the steel inner ring, and is protected by both of them, so that the tightening torque of the bolt can be reduced at least Double the sealing performance without reducing the sealing performance, extending the service life of the thread and reducing the production cost.
Nuts are very common fasteners. Generally, the torque cannot be limited when the nut is twisted. The degree of tightness of the nut is mostly judged by the worker's experience. In this way, when the nut is over-tightened, it will lead to the destruction of the thread pair, thereby shortening the fastener. The life of the nut may even cause the bolts to be pulled off in severe cases; and the nut is too loosely screwed, which will lead to the problem of insecure fixing.
The material of the combination screw is divided into iron and stainless steel. The iron ones are made of different iron screw wires. Generally, the wire of the combination screw is 1010, 1018, 10B21 and so on. 10B21 is used to make 8.8 grade combination screws. Like 8.8 grade hexagon socket head combination screws, 10B21 wire is often used. When done, go to heat treatment. After heat treatment, remove hydrogen and electroplating. This is to prevent the spring washer of the socket head cap screw from breaking. Stainless steel combination screws, in the combination screw market, generally refer to stainless steel SUS304 combination screws. 201 combination screws generally do very little. Few combination screw manufacturers produce 201 combination screws. Because the hardness of the screw wire of stainless steel 201 is not well controlled, it is easy to produce cracks.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: open spring washers, copper pillars supporting copper pillars motherboard, nylon mesons, extended outer screws and other products, we can provide you with suitable fasteners for you solution.
