Service HotlineMake further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 447N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
At present, the installation methods of the retaining ring: 1. Most of them are installed with retaining ring installation pliers; 2. Simple installation aids; 3. Automatic retaining ring installation machine. The disadvantages of these installation methods: 1. If the manual installation is uneven, the elastic retaining ring will deform plastically, which will cause the elastic retaining ring to fail; 2. It cannot be positioned for complex structural parts, and the production efficiency is also low; 3. Simple installation Auxiliary tools are only suitable for the parts to be installed, which are generally not universal and have limitations; 4. The automatic elastic retaining ring installation machine has a complex structure and high cost.
In the existing life, repair parts are often used to repair the cassettes with damaged screw holes, and the screw holes on the repair parts are used instead of the original damaged cassette screw holes. However, in the prior art (application number: 201520948368.1), the restoration is fixed by rotating the support of the restoration, which is often inconvenient due to the small space of the cassette. In addition, the set screw in the prior art mainly fastens the object through the end of the screw without threaded holes, which makes it difficult to install external screws. Based on this, a method of extruding the support through a set screw with screw installation holes and tightening the repair piece, and then installing the screw on the set screw, will facilitate the quick installation and use of the repair piece.
At present, many manufacturers do not want the product to be disassembled by the user, so they set the anti-disassembly mark on the product. The common method is to apply red or blue anti-disassembly paint on the fastener, such as the nut, once the user disassembles it by himself. , the paint at the connection will fall off, and it can no longer be aligned, so that the manufacturer can judge and identify it and provide a basis for warranty. However, it is inconvenient to paint some joints, and the use of tamper-evident paint is not healthy and environmentally friendly.
For achieving the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solutions: a pin, comprising a pin cap and a described pin rod, the pin cap and one end of the pin rod are fixedly connected, and the pin rod There is a convex body, the convex body is fixedly connected with the pin rod, the convex body is located on the pin rod rod body, and the other end of the pin rod is provided with a top connecting body, and the top connecting body is fixedly connected with the pin rod , the top contact body includes several top contact units and discs, each top contact unit is coaxially arranged with the pin rod, the top contact units are sequentially fixedly connected along the axis direction of the pin, the top contact unit is The major diameter of the outer contour of the connecting body is larger than the diameter of the pin rod.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: iron galvanized square nuts, machine wire hand-tightened ring screws, pressure riveting parts with an outer diameter of 5.4 negative, torx three combination screws and other products. We can provide you with the right fastener solution for you.
