Service HotlineIn the prior art, the beams used for installing the curtain wall are mainly divided into two types: closed-cavity structure and open structure, and angle aluminum connection is mainly used for the connection between the beam and the column. As far as the beam of the closed-cavity structure is concerned, after the angle aluminum is used to connect, there are open bolts on both ends of the upper surface of the beam, and the aesthetic performance is extremely poor. As far as the beam of the open structure is concerned, in the actual connection, first fix one corner of the angle aluminum to the beam, and then connect the other corner of the angle aluminum to the column; due to the limited operating space in the beam of the open structure, the angle aluminum is not It is easy and accurate to install, and it takes a lot of time to install; and when the curtain wall panel is heavy, the beam will be twisted, causing the gusset of the opening part of the beam to fall. In addition, due to the limitation of the opening structure itself (an additional gusset or clasp), the aluminum content of the beam is relatively heavy, and the manufacturing cost is high.
A T-bolt. This kind of bolt includes a bolt shank and a bolt head, and the bolt head adopts a special cylindrical bolt head, which can be suitable for installation and cooperation of various sizes. Although the shape of such a bolt head is greatly improved compared to the square bolt head in the prior art, the cylindrical bolt head is particularly inconvenient to install, and special installation tools must be used for installation. If the manual direct installation method is adopted, since the force area of the finger touching the side of the cylinder is small, it will increase the difficulty of the installation work and needs to be improved.
In another embodiment of Guangdong Yueluo Hardware Industrial Co., Ltd., the conveying device 3 includes a motor 31 and a circular rotating disk 34, the motor 31 drives the circular rotating disk 34 to rotate, and the circular rotating disk 34 is evenly provided with screws in the circumferential direction. The matching screw accommodating hole 35, the screw enters the screw accommodating hole 35, the motor 31 drives the circular rotating plate 34 to rotate, so that the screw is first slotted by the cutting wheel 42, and then polished by the fixing wheel 48, and the screw is in the screw accommodating hole 35. It is fixed, which is more secure and reliable during the slotting process. Preferably, the circular rotating disk 34 includes a circular rotating disk 32 and a sector-shaped fixed disk 33. The circular rotating disk 32 is evenly provided with screw receiving recesses matching the screws in the circumferential direction, and the recesses and the sector-shaped fixed disk 33 are formed with the screws The matching screw receiving holes face the cutting wheel 42 and the fixing wheel 56 .
Countersunk head, half countersunk head, 1200 countersunk head, half countersunk head rivets are mainly used for riveting occasions where the surface needs to be smooth and the load is not large. Flat head rivets are used for riveting occasions subject to general loads. Flat head and flat head rivets are mainly used for riveting of metal sheets or non-metallic materials such as leather, canvas and wood. Large flat head rivets are mainly used for riveting of non-metallic materials. Semi-hollow rivets are mainly used for riveting occasions with little load. Headless rivets are mainly used for riveting of non-metallic materials. Hollow rivets are light in weight and weak in head, and are used for riveting of non-metallic materials with little load. Tubular rivets are used for unloaded riveting of non-metallic materials. Nameplate rivets are mainly used for riveting nameplates on machines and equipment.
The heating bolt pre-stretching method makes the bolt pre-stretch to the required deformation amount by heating, and then tighten the nut. After cooling, the bolt is shortened and the connection is pre-tightened. This is a commonly used fastening method in infrastructure installations. However, it is not suitable for devices that often need to be disassembled and adjusted, because during the disassembly process, the connected parts will be heated and elongated together with the bolts, and the use of open flame heating will be limited in some occasions; the use of electric heating will make the structure of the screw It becomes complicated and increases the investment, and even if it is difficult to disassemble, such as the propeller shaft of the ship, etc., the heating method is not suitable.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: B-grade equal-length bolts, connecting rod locks, 511 small saddle-shaped single-sided tooth washers, screw and nut sets and other products, we can provide products such as You have the right fastener solution for you.
