Service HotlineGenerally, the T-bolt structure is common, and its blank shape can be completed at one time on a multi-station cold heading machine. But for T-bolts with relatively rare structures, (for example: the intersection of ¢14x42 cylinder (head) + ¢12 cylinder, the two cylinders form a 90° intersection) due to the special structure, the head Cold forming is difficult, and the traditional processing route is: die casting blank → deburring → turning processing → grinding blank diameter → wire rolling → heat treatment → surface treatment → finished product packaging.
door cover structure with hidden screws includes a glass panel, an inner door cover, a computer board and a sealing strip, an adhesive bracket is adhered to the back of the glass panel, the inner door cover is fixedly connected with the adhesive bracket through screws, and the computer board is arranged on the glass panel. In the cavity formed by the panel and the inner door cover, the inner door cover is provided with a sealing slot, the sealing strip is embedded in the sealing slot, and the bottom of the sealing slot is provided with a mounting hole for the screw to pass through, and the glue The bracket is provided with a fixing hole matched with a screw thread, and the screw passes through the installation hole of the inner door cover and is threadedly connected with the fixing hole of the adhesive bracket, so as to fixedly connect the inner door cover and the glass panel. The screw is hidden in the sealing groove of the door cover, and is sealed with water through the sealing strip. The appearance is beautiful, easy to disassemble and assemble, and it can effectively protect the screw from rust.
The diameter, length and quantity of the stud bolts shall meet the requirements, and the type and material of the stud bolts shall be determined by the grade. There are two types of commonly used stud bolts (also known as full-threaded studs). The thread is divided into two types: coarse thread and fine thread. The coarse thread ordinary thread is expressed by M and the nominal diameter, and the fine thread ordinary thread is expressed by M and the nominal diameter × pitch. The fastener standard stipulates that M36 bolts use coarse thread, M36 and above diameters can use fine thread, and the pitch is 3. bm=1d studs are generally used for the connection between two steel connected parts; bm=1.25d and bm=1.5d studs are generally used between cast iron connected parts and steel connected parts The connection between the two; bm=2d double-ended stud is generally used for the connection between the aluminum alloy to be connected and the steel to be connected. The former connector has internal threaded holes, and the latter connector has through holes. The threads at both ends of the equal-length studs need to be matched with nuts and washers, and are used for two connected parts with through holes. One end of the welding stud is welded on the surface of the connected piece, and the other end (threaded end) passes through the connected piece with a through hole, and then the washer is put on, and the nut is screwed on, so that the two connected pieces are connected as a whole.
A screw suitable for a variety of tools is a single-structure threaded part, including a screw body and a screw head. The outer surface of the screw body is processed with an external thread 1, and the outer side of the screw head is formed by six screw heads. Prismatic, the top surface of each edge of the outer hexagonal prism is a boss, between each boss is an end face groove 4, and the middle of each boss is provided with an end face hole 3; the inner side of the screw head is formed by six screw heads. The side surface 5 forms an inner hexagonal prism hole, and the bottom of the inner hexagonal prism hole is processed with a cross groove 16 .
However, Yueluo still feels that there should be room for improvement for the screw improvement and screw that integrates stability, labor, fast and multi-function in the above two cases; for example, No. 556784 screw improvement Although the rod has the function of cutting and collecting chips, when the screw starts to screw into the object such as wood, it is hindered by the hardness of the object's tissue, so the staff still needs to exert considerable force, resulting in the lock. In the solid operation, there is still a lack of difficulty in screwing in operation; another example, new cases such as No. 289408 screw that integrates locking, stability, labor, fast and multi-function, although the rod has the structural function of cutting and chip removal, it is The rod part is screwed into the middle section to the rear section of the object. Since the debris cannot be discharged, the rod part pushes the outer part of the object to the surrounding tissue of the object, so that the object expands outwards and even seriously damages the appearance of the object.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: set electronic screws, screw screws for T-slots, disc spring washers, knurled non-standard fasteners and other products, we can help you Provide the right fastener solution for you.
