Service HotlineThe existing method of tightening large screws is generally 1. After the nut is screwed to the connected piece by hammering + nut angle method, use a casing to connect the lever arm of the wrench, or use a free hammer to hammer the plate handle, Rotate the nut an additional angle to obtain the required preload. This is not only a primitive and labor-intensive fastening method, but also has great limitations, such as limited space, or the screw itself is a rotating shaft and so on, it is difficult to use this method.
For common screw belts, please refer to the Central Taiwan Announcement No. 327442 Screw Belts (2) on February 21, 1998. It includes a main body, and there are multiple grooves on the side of the main body, which are used for locking screw tools to drive the belt. A toggler; and a plurality of nail grooves are arranged on the nail belt so that the screw planting is arranged in an arrangement, and the nail grooves are all provided with through holes, and the through holes extend downward with a ring to form a support portion for the screws; and the It is surrounded and provided with a plurality of cutting grooves, which is beneficial for the screw to be rotated through the nail groove; and it is characterized in that the nail groove is located on the inner wall surface of the surrounding and is provided with a plurality of lobes, and these lobes are implanted in the screw. In the nail groove, the leaflet supports the screw, so that the screws with different outer diameters are fully supported and positioned by the leaflet; and/or the upper part of the leaflet is inclined or curved, so that a depression is formed above the ring to support the screw The arc surface or tapered surface of the neck can make the screw more stable to be supported.
Fasteners are a type of mechanical parts that are used for fastening connections and are widely used. Fasteners are used in a wide range of industries, including energy, electronics, electrical appliances, machinery, chemicals, metallurgy, molds, hydraulics, etc., in various machinery, equipment, vehicles, ships, railways, bridges, buildings, structures, tools, instruments, etc. , chemical industry, instruments and supplies, etc., you can see all kinds of fasteners, which are the most widely used mechanical basic parts. It is characterized by a wide variety of specifications, different performance uses, and a very high degree of standardization, serialization and generalization. Therefore, some people also refer to a type of fasteners that have been standardized as standard fasteners, or simply referred to as standard parts.
The bolt thread is generally cold worked, so that the thread blank within a certain diameter range passes through the rubbing (rolling) wire plate (die), and the thread is formed by the pressure of the wire plate (rolling die). The plastic streamline of the threaded part is not cut off, the strength is increased, the precision is high, and the quality is uniform, so it is widely used. In order to make the outer diameter of the thread of the final product, the required thread blank diameter is different, because it is limited by factors such as thread accuracy and whether the material is coated or not. Rolling (rubbing) thread is a processing method that uses plastic deformation to form thread teeth. It uses a rolling (screwing plate) die with the same pitch and tooth shape as the thread to be processed, while extruding the cylindrical screw blank, while rotating the screw blank, and finally transferring the tooth shape on the rolling die to the On the screw blank, the thread is formed. The common point of rolling (rubbing) thread processing is that the number of rolling revolutions does not need to be too much. If it is too much, the efficiency will be low, and the surface of the thread teeth will easily cause separation or random buckle. On the contrary, if the number of revolutions is too small, the diameter of the thread is easy to be out of round, and the pressure at the initial stage of rolling increases abnormally, resulting in a shortening of the life of the die. Common defects of rolled threads: cracks or scratches on the surface of the thread part; random buckles; out of roundness of the thread part. If these defects occur in large numbers, they will be discovered during the processing stage. If the number of occurrences is small, the production process does not notice these defects and then circulates to users, causing trouble. Therefore, the key issues of processing conditions should be summarized, and these key factors should be controlled in the production process.
The screw is a fairly common structure in the technical field of machine parts assembly, and it mainly uses the mutual engagement characteristics of male and female threads to achieve the purpose of pressing the workpiece. At present, there are many kinds of screws on the market, and their functions are also very different. However, a stud and a rotating part by which the stud is rotated are the same basic structure.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: BS3410 gaskets, HG screws, rubber gasket O-rings, screw and screw connections and extended hexagonal round nuts and other products, we can provide You have the right fastener solution for you.
