Service HotlineThe embossing wheel is used to press the mesh pattern (rolling mesh pattern), and the middle is slotted. After milling, the thread still guarantees 6H accuracy. This knurled copper nut is used in power tools, which is different from other knurled copper nuts. The diamond pattern of this knurled copper nut is located in the middle section of the product, and the diamond-shaped mesh knurling wheel rolls the diamond-shaped flower along the large outer circular step surface.
Round head three-combination screws are also called pan-head three-combination screws, which are divided into large pan-head three-combination screws and small pan-head three-combination screws. The materials are divided into stainless steel and iron. The stainless steel round head three-combination screws include stainless steel small pan head three-combination screws and stainless steel large pan-head three-combination screws. The national standards are respectively expressed as GB9074.8 and GB9074.4.
Riveting nut tool is a special installation tool for riveting nut, including pneumatic riveting nut and electric riveting nut. Pneumatic riveting nut tool has the advantages of fast speed and large pulling force, but it is difficult to rotate into and unscrew the riveted nut. The rotating blade of the moving motor is frequently used or in a slightly dusty working environment, it will suddenly get stuck and not work, there is a great hidden danger of motor crash, and the torque of the air motor is small due to the limitation of the volume, although the riveting pulling force can be done to larger defects, but the volume also increases.
In order to solve the above-mentioned technical problems, the technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is: shear rivets, including a mandrel and a deformation sleeve ring sleeved on the mandrel, one end of the deformation sleeve ring is a boss structure, and the It includes an adhesive collar sleeved on the deformation collar, the adhesive collar is a hollow annular sleeve and is filled with adhesive material; one end of the mandrel is a hemispherical head, and the spherical surface of the hemispherical head is outward, The connection between the hemispherical head and the mandrel is a conical connecting section, and the diameter of the conical connecting section gradually decreases from the hemispherical head inward; the mandrel is provided with a stress concentration groove, and the position of the stress concentration groove is close to the deformation The boss structure of the collar.
1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.
We have many years of experience in the production and sales of screws, nuts, and flat washers. Firmware Solutions.
