Service HotlineDowels are made on the steering seat on the ball head of the car, and the rollers are assembled to the steering seat through the dowels. The prior art is manual driving of the pins, and the position of the pins is inaccurate when driving the pins, the labor intensity is high, the efficiency is low, and the quality of the steering seat is also affected. Therefore, it is necessary to design an automatic pin-driving mechanism to drive the pins into the steering seat. .
Use performance self-tapping screws for self-tapping screws with a diameter of 0.8mm to 12mm. For this type of screw, it generally has a high hardness. Self-tapping screws must be screwed into the test, that is, screw the screw into a test plate to check whether the hardness of the screw meets the standard. The shape of the drill tail, the hardness of this kind of screw is very strong. Compared with ordinary screws, it not only has better maintenance ability, but also has a very strong effect in connecting objects. For screws with this performance, it is generally not necessary. Auxiliary processing can directly drill a hole on the object and lock it into the object, which is not only very convenient to use, but also greatly improves work efficiency. This kind of drill screw can be said to be the first choice of the staff in various fields.
The elastic cylindrical pin, also known as the spring pin, is a headless hollow cylindrical body, which is slotted in the axial direction and chamfered at both ends. It is used for positioning, connection and fixation between parts. The outer diameter of the spring pin is usually slightly larger than the mounting hole. The deformation force generated by the elastic cylindrical pin to be restored to its original state by extrusion ensures the clamping effect of the elastic cylindrical pin. But just because of its clamping effect, it will play a big obstacle to the disassembly of the elastic cylindrical pin. When in use, the open end is extended out of the through hole on the pin shaft, and the open end is flared and separated to prevent the elastic cylindrical pin from sliding off the pin shaft to realize the function of preventing backlash. At present, the disassembly method of the elastic cylindrical pin usually uses a punching machine to remove the cylindrical pin, which easily destroys the equipment installed on the cylindrical pin, and the disassembled elastic cylindrical pin cannot be used again due to damage. One method is to insert the mounting pin with the clearance fit of the mandrel, punch the pin behind the mandrel to clamp the bottom of the cylindrical pin, and then pull out the cylindrical pin, which can only be used when the elastic mounting pin is installed in the through hole, and because it is necessary Applying force to the mandrel increases the difficulty of disassembly and increases the work intensity of the installer. Three methods are done by the installer using two needle nose pliers. Specifically, first use needle-nose pliers to clamp the ends of both sides of the elastic cylindrical pin, and then apply an inward force to the needle-nose pliers, so that both sides of the elastic cylindrical pin rotate in the same direction until the opening becomes smaller, and then Pull it out to remove it successfully. The defects of these existing methods are obvious. The shape of the disassembled elastic cylindrical pin is either unusable or the deformation of the cylindrical pin after disassembly is not uniform, which seriously affects the performance of the elastic cylindrical pin, resulting in waste and increased cost; The method is purely manual work, and sometimes it takes several repetitions to remove the elastic cylindrical pin. Due to the different installation positions of the elastic cylindrical pin, it sometimes increases the difficulty of disassembly, and it is difficult to remove the needle-nose pliers effectively. The pliers are difficult to construct, and the elastic cylindrical pins are easily damaged. If there are too many elastic cylindrical pins to be disassembled, the existing methods are often difficult to meet the needs, which not only consumes a lot of time and physical strength of the installer, but also makes it difficult to ensure the quality.
In the current plastic matrix, it is common to use self-tapping screws or add copper inserts during injection molding. The former has poor strength, and the threaded hole is easy to crack; the processing cost is high, the injection molding efficiency is low, the labor cost and manufacturing cost are increased, and the insert is easy to slip and crack on the plastic, and the thread strength of the copper insert is not as high as that of the iron nut.
The flat washer is mainly used to reduce the pressure. When some parts are tightened with a large axial force, it is easy to press the washer into a dish shape. At this time, it can be solved by changing the material and increasing the hardness.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB860 black saddle elastic washers, full-tooth fine-tooth screws, countersunk head slotted screws, thin washer mesons and other products, we can provide you Provide the right fastener solution for you.
