Service HotlinePins are widely used. In the connection of the rotating mechanism of two moving components, such as the crank mechanism, the turning mechanism, the connection between the hydraulic cylinder and the moving parts, the pins are used. kind. In order to ensure the normal use of the running equipment and prevent the cylindrical pin from slipping out and falling off during use, some anti-falling methods are usually used at the head of the pin, such as 1. Drill holes and insert cotter pins to prevent the pins from slipping out; 2. The external thread is tightened with a nut to prevent the pin from slipping out; 3. The slot is clamped with a circlip to prevent it from slipping out, etc. These measures make the cylindrical pin very practical in the case of infrequent disassembly and assembly, but in the actual use of the field, in order to prevent the collision of some equipment during each troubleshooting or maintenance, the pin needs to be pulled out and turned up, etc. After the failure or maintenance is completed, put down and then insert the pin to restore, this process will bring trouble to the actual operator. For example, special tools must be brought with you every time you disassemble and assemble the pin, and the split pin or the circlip is easily damaged after repeated disassembly and assembly. , In order to save trouble, the operator sometimes uses iron wire to thread or fasten it instead, and even does not remove the pin for the sake of speed and convenience, which is easy to cause damage to the equipment when dealing with faults.
Semi-round head plastic screws have high-quality characteristics such as insulation, non-magnetic, corrosion resistance, beautiful appearance, and never rust, and modified engineering plastics, its strength and impact resistance are comparable to those of metals. The plastic screws we often say are commonly known as nylon. After adding 30% glass fiber to the screw, its mechanical properties are far superior to ordinary nylon. The materials used for the dome head plastic screws are becoming more and more diverse, the performance is constantly improving, and the application fields are becoming wider and wider. 1. Medical equipment industry (insulation, non-magnetic, environmental protection, anti-interference, make medical equipment safer to use) 2. Wind power industry (isolation and insulation of chassis circuit PCB boards) 3. Aerospace industry (electronic equipment Insulation, anti-interference) 4. Office equipment industry (never rust, beautiful and practical) 5. Petrochemical industry (high temperature resistance, chemical resistance, corrosion resistance, prolong equipment life) 6. Electronics industry (insulation, anti-interference) , light weight) 7. Communication industry (insulation, non-magnetic, safety) 8. Ship industry (acid resistance, alkali resistance, corrosion resistance, extended service life), etc... .
In the process of automatically locking the screw to the product, there are only three types of screw supply mechanisms in the traditional automatic screw locking machine: 1. Magnet sucks for screws; 2. Vacuum sucks for screws; 7. Air blows for screws. The above three methods require long-distance screw supply, resulting in slow screw supply, low efficiency and high manufacturing cost. To this end, we propose an automatic locking screw machine that can directly supply screws.
The fixing screw proposed by Guangdong Yueluo Hardware Industry Co., Ltd. has a screw body 1, and the axial surface of the screw body 1 is formed with extending screw teeth 6, and the axial surface is a column along the central axis direction of the cylinder of the screw body 1. The body surface has a hemispherical screw tail 7 at the bottom, and a screw head 2 at the top. The upper surface of the screw head 2 is provided with a slot (not shown). The screw body 1 is composed of the upper tapered rod 4 and the lower cylindrical screw 5. The tapered rod 4 is an inverted cone, the diameter of its circular upper surface and the diameter of the screw mounting hole 10. equal. The fixing screw also has a washer 3, the washer 3 is arranged between the screw head 2 and the screw body 1, the lower surface of the cylindrical washer 3 has a number of teeth 8, the teeth 8 are along the The upper surface of the inverted cone of the tapered rod 4 and the edge of the washer 3 are connected to form a straight convex strip 15 extending outward; the convex strip 15 can also be designed in an arc shape. The fixing screws for installation proposed by Guangdong Yueluo Hardware Industry Co., Ltd. can be made of metal materials in one piece. As shown in Figure 3, it is a schematic diagram of the installation of Guangdong Yueluo Hardware Industry Co., Ltd. for PCB board fixing. When installing, first pass the screw body 1 of the fixing screw through the mounting hole 10 and the copper column 11 provided on the PCB board 9, so that the tail 7 of the screw reaches the mounting hole 13 on the casing 12, and then use the tightening tool 14 to insert the screw At the notch on the top of the head, forcefully press the inverted cone design taper rod 4 of the screw body 1 into the mounting hole 10, so that the tail 7 passes through the mounting hole 13. Due to the outer diameter D at the bottom of the taper rod and the screw mounting hole The aperture size of 10 is equal, and the fixing screws are pressed and fixed, so that the PCB board 9 can be automatically corrected in the process of fixing its front, back, left and right deflections, and the accuracy of the installation position of the PCB board 9 can be ensured. As shown in Figure 4, after the fixing screw is screwed into the casing, the washer 3 is fully contacted and pressed on the PCB board 9, and the PCB board 9, the copper column 11 and the casing 12 are firmly connected together without sliding. . The teeth 8 on the washer 3 are in full contact with the surface of the PCB board 9, so that a ground wire path is set up between the PCB board 9 and the casing 13 by the metal fixing screw 1, thereby ensuring that the PCB board 9 is fully grounded , the design of the teeth 18 on the washer 3 also has a non-slip function. The fixing screws for installation designed by Guangdong Yueluo Hardware Industry Co., Ltd. make use of the cooperation, friction and electrical conductivity in the mechanical connection, which fully guarantees the firm installation of the PCB board and the chassis and the good grounding of the PCB board. Moreover, the ellipsoid tail of the fixing screw The surface is relatively smooth, even if the mounting holes are exposed, it will not cause scratches on the hands and desktop. The above is only the embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., and does not limit the scope of Guangdong Yueluo Hardware Industry Co., Ltd., any equivalent structure made by using the contents of the description and drawings of Guangdong Yueluo Hardware Industry Co., Ltd. or etc. Effective process transformation, or direct or indirect application in other related technical fields, are also included in the protection scope of Guangdong Yueluo Hardware Industry Co., Ltd.
through-hole mounting nut, comprising a hexagonal portion 1 and a cylindrical portion 2, a threaded hole 3 is provided between the hexagonal portion 1 and the cylindrical portion 2, and two grooves 4 are opened on the cylindrical portion 2, and each of the two sides of the groove 4 has a The raised side 5, the two sides protruding from the sheet metal part 7, if squeezed or hit by the bolt 8, it will bend to both sides and buckle on the sheet metal part, so that it is not welded directly. Rubber can also be used. Each of the upper surfaces of the side edges 5 is provided with a convex point 6 so that the hammer will not slip when hitting.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: national standard lifting ring screws, round cup screws with pads, nylon concave hole countersunk hole washers, flat head bare body blind hole rivet nuts and other products, we can provide products such as You have the right fastener solution for you.
