Sometimes, the iron screws are often seen broken, and sometimes, the stainless steel screws are also seen broken. But generally speaking, stainless steel screws rarely break. Because the stainless steel screw wire itself is relatively hard. But under certain circumstances, stainless steel screws can still break. So what are the main reasons for stainless steel screws to break? The reasons for the fracture of stainless steel screws are as follows: 1. The quality of raw materials used for stainless steel screws is poor, and the quality of stainless steel screws is not good. There are many impurities, impure, resulting in insufficient hardness of stainless steel screws. 2. The production process of stainless steel screws. For example, stainless steel screws with eccentric head and eccentricity, and the Q value is too deep and the R position design is too small during the down punching operation during production. 3. The customer uses too much force when using stainless steel screws. Generally, you do a torque test to see how much the minimum breaking force is, and then adjust the torque. Of course, stainless steel screws must be broken for more than three reasons. But the above three reasons are the main reasons for the fracture of stainless steel screws. When the stainless steel screw is found to be broken, it can be checked step by step. Find out what's causing it.
However, although the existing screws can meet the function of connecting and fastening objects, they are all pressed against the object by the head to achieve the purpose of pressing and fixing. However, due to the small size of the head, it is difficult to press the object firmly. , for this reason, only spacers can be added to increase the pressing area. However, in the assembly process, the gasket is prone to slip off, and it needs to be supported by hand, which brings inconvenience to installation and use; at the same time, sometimes the object to be pressed is only on one side of the screw, and the other side of the screw does not need to be pressed. This results in unnecessary waste of materials, and also occupies a certain space, which brings trouble to the installation of other components.
In chemical production equipment, the cylinder body and the head cover need to be connected and sealed. The traditional sealing structure is to connect the two with a screw, add a non-metallic gasket in the middle and fix it with a nut. However, such a sealing structure only controls the tightening torque, and has the technical defect that the sealing ring will be twisted or even broken during repeated loading and unloading of the cylinder head cover, resulting in poor sealing performance.
In order to achieve the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solutions: an anti-drop screw structure, including a connecting bolt and a fastening screw, the connecting bolt includes a connecting screw and a connecting nut, one end of the connecting screw It is integrally connected with the connecting nut, the surface of the connecting screw is provided with an external thread, the connecting bolt is movably mounted with a matching nut, the matching nut and the connecting bolt are connected by thread, and the interior of the connecting screw is provided There is a screw hole along the axis of the connecting screw. The connecting screw is provided with a number of slots along the axis. The slot extends into the screw hole. The screw hole is provided with an internal thread, and the screw hole is movable in the screw hole. A tightening screw is installed, the tightening screw includes a tightening screw and a tightening nut, one end of the tightening screw is integrally connected with the tightening nut, and the tightening screw is connected to the tightening nut through a screw hole Bolted thread connection.
In order to solve this technical problem, Yueluo Company provides an adjusting nut, which includes a bearing unit, a thrust washer, an adjusting nut and a snap ring. The inside of the adjusting nut is an internal thread structure, and one end of the internal thread structure is provided with Ring groove, the snap ring is pressed into the ring groove with interference, and is rigidly connected with the adjusting nut without relative movement; the bearing unit is supported on the shaft, and the thrust washer is in plane fit with the bearing unit; the adjusting nut and the shaft are threadedly connected , Fit with the thrust washer plane, the inner diameter of the snap ring and the thread of the shaft are in interference fit.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: black zinc plated 304 screws, carbon steel galvanized, GB120 medium carbon pins, grade A carbon steel galvanized bolts and other products, we can provide you with The right fastener solution for you.