Service HotlineStainless steel screws do not necessarily corrode and rust, but that stainless steel screws have a stronger ability to withstand corrosion and rust than iron screws. But stainless steel screws can still rust under certain circumstances. So under what conditions are stainless steel screws prone to rust! What is the cause of rust? Stainless steel screws have better characteristics, strong corrosion resistance, high temperature resistance, and strong rust resistance. But it will rust in harsh environments. For example, stainless steel screws are exposed to the sun and the wind every day under very humid conditions. Over time, it will definitely rust a little. For example, in contact with some acid-base chemicals to cause chemical reactions. cause corrosion and rust. There are also bad stainless steel screws, such as stainless steel SUS201 screws used in seawater. Due to long-term immersion, SUS201 stainless steel screws themselves are not suitable for use in salty seawater. cause corrosion and rust. For the use of marine products, it is generally recommended to use stainless steel SUS316 screws, because 316 stainless steel screws have better performance such as corrosion resistance. From the above, it can be concluded that stainless steel screws will still corrode and rust under certain circumstances. Therefore, this requires the rational use of stainless steel screws. Use stainless steel screws of different materials in different situations. And in different occasions, when using stainless steel screws, special attention is also required, and some details need to be considered more. Try to control the corrosion and rust of stainless steel screws as much as possible.
However, due to a radial external tension, the external tension is caused by the tightening axial force generated by the tightening torque, and the phenomenon of open ring expansion occurs, and the spring washer often breaks due to hydrogen embrittlement. The nut exerts uneven pressure on the flat washer through the spring washer. And the friction coefficient between the spring washer and the nut and the flat washer is very small, and the phenomenon of vibration, rotation and relaxation occurs.
The rivet provided by Yueluo Creation includes a mandrel and a coaxial matching nail sleeve outside the mandrel; the mandrel includes a head, a central rod and a tail, and a position close to the head is provided with an inner A concave section of the lock ring area, a position close to the tail is provided with a section of lock area that inclines and shrinks inward along the direction of the head to the tail; the lock ring area of the core rod is gap-fitted and fixed with a lock ring , a part of the lock ring is located inside the sleeve head of the nail sleeve, and the part of the lock ring located outside the sleeve head of the nail sleeve can be interference fit with the nail sleeve; the nail sleeve The sleeve is provided with a through hole for the core rod to penetrate into, the inner wall of the nail sleeve forming the through hole is provided with a protruding structure, and one end of the protruding structure is close to the sleeve head of the nail sleeve The end of the core rod is close to or adjacent to the end of the tail of the core rod.
At present, with the continuous growth of the demand for communication products, higher and higher requirements are put forward for the production capacity of equipment manufacturers, and at the same time, the requirements for the cost, weight and reliability of communication products are also more and more stringent. In order to facilitate the positioning of the equipment, pins are often used to complete the equipment, and a certain cost is incurred for its manufacture and assembly. In the past, such parts have been assembled in the form of threads. In order to ensure that the assembly height is within the specified range and to prevent loosening, bar turning is often used to form threads and positioning steps, and thread pinning glue is used in the assembly, and the cost of machining is relatively high. Large, more material waste. Based on the above drawbacks, in order to better solve this problem, some existing manufacturers use the interference fit riveting method, which solves the problem of material waste and anti-loosening, but the inner diameter of the pin hole and the outer diameter of the pin are matched. The machining accuracy of the machine is relatively high. Once the matching size is out of tolerance, a second matching is required, which wastes working hours and increases the slack time.
The shaft circlip is a mechanical part installed on the slotted shaft and used as a fixed part for the movement of the hole. The inner diameter of the shaft circlip is slightly smaller than the mounting shaft diameter. When installing the shaft circlip, use the circlip pliers, insert the pliers into the pliers hole of the retaining ring, expand the retaining ring, and then put the shaft circlip into the shaft groove.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: grade 8 fine pitch black hexagon nuts, twist star plastic screws, thin hexagon nut bolts, thick nuts and other products, we can provide you with The right fastener solution for you.
