Service HotlineNuts are a commonly used fastening parts and are widely used in various mechanical and electrical equipment. Common application equipment does not have particularly strict requirements on the anti-loosening properties of nuts, but for automobiles, high-speed railways, aerospace and nuclear power and other fields, many equipment or components work in a vibration environment for a long time, and it is easy to loose between bolts and nuts. This will affect the normal operation of the equipment and even cause safety accidents.
T-slot convenient bolt that can be used for the middle port of the T-slot and directly realizes the assembly and tightening of the bolt and the nut. Technical Background At present, the bolts for T-slots are assembled from two side ports of the T-slots. When the length of the T-slot is long, it is time-consuming and laborious to install from the side port to the center port at the designated position. In addition, the two side ports of the T-slot are often blocked by other components, and the bolts for the T-slot cannot be installed or removed without disassembling other components. The utility model makes some improvements to the prior art. SUMMARY OF THE INVENTION The purpose of the present invention is to provide a T-slot convenient bolt with simple structure and convenient mounting and dismounting for the current situation that the existing T-slot bolts are inconvenient to install and disassemble.
In the prior art, there are also automated equipment for riveting and assembling of hardware and handles; however, for the existing automated equipment, how to automatically and efficiently realize rivet feeding is particularly important.
Among them, the pneumatic riveting machine is more commonly used. The pneumatic riveting machine is also equipped with a clamp for assembling the rivet. The existing clamp usually uses two rotating clamps for fastening and assembly, but the rotation easily causes the two clamps to buckle. Misalignment, thus affecting the assembly of the rivet.
When using screws, if you can understand the mechanical properties of screws first, then you can use screws better. Different types of screws have different mechanical properties, and the different mechanical properties lead to different occasions when screws are used. 1. Self-tapping screws: mechanical performance requirements 1. Heart hardness: standard value HRC28-38. When testing, take the section 1-2 times the diameter of the name from the tail. If the length of the name is too short, it can be embedded first, and then the hardness is measured. 2. Surface hardness: standard MIN HV450. 3. Carburized layer: standard 4#-6#: 0.05-0.18mm, 8#-12#: 0.10-0.23 mm, 14#: 0.13-0.28 mm. The main purpose of carburizing is to enhance the surface hardness and ensure the strength of the teeth. If the decarburization is too deep and the carburization is insufficient, the strength of the teeth will not meet the requirements, that is, the teeth will be damaged during the screw-in test. 4. Torque: standard specification 4#5#6#7#8#10#12#14#A tooth 14212835455696145AB tooth 142128354565102165. 5. Screw-in test: screw the self-tapping screw into a steel plate with a reserved test hole. The self-tapping screw should form a matching thread in the test plate, and the thread of the screw itself will not be deformed or damaged until the end. Tapered threads pass completely through the test plate. The screw-in test is only applicable to AB, B, BP and other types of self-tapping screws. It is stipulated in IFI that the test plate shall be prepared from semi-hard low-carbon cold-rolled steel, and the hardness of the steel plate is 70–85HRB in Rockwell. The standard specification of the steel plate, that is, the thickness, is shown in the table below. The test hole should be punched or drilled, and the tolerance is the specified nominal diameter (see the table below) ± 0.025mm. Specifications 6#7#8#10#12#1/4 Test plate thickness (mm) 1.85-1.953.12-3.234.68-4.84 Aperture (mm) ±0.0252.953.263.454.044.765.50.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: processed bolts, 304 lock nuts, long nuts, 12.9 teeth 1.5 screws and other products, we can provide you with suitable fasteners for you solution.
