Service Hotline(1) The surface rust, oil stains, burrs on the wall of the bolt holes, welding flashes, etc. should be cleaned up. (2) After the contact friction surface is treated, the specified anti-scratch coefficient requirements must be met. The high-strength bolts used should have matching nuts and washers, which should be used in accordance with the matching and should not be interchanged. (3) When the friction surface of the treated component is installed, it is not allowed to be stained with oil, soil and other sundries. (4) The friction surface of the module should be kept dry during installation and should not be operated in the rain. (5) Strictly check and correct the deformation of the connected steel plates before installation. (6) It is forbidden to hammer into the bolt during installation to prevent damage to the bolt thread. (7) The electric wrench, which is regularly tested during use, ensures the accuracy of the torque and operates in the correct tightening sequence. Main safety technical measures (1) The size of the wrench of the adjustable wrench should be consistent with the size of the nut, and the sleeve should not be added to the small wrench. A dead wrench should be used for high-altitude work. For example, when using an adjustable wrench, use a rope to fasten it, and people should fasten their seat belts. (2) When assembling the connecting bolts of steel components, it is strictly forbidden to insert your hands into the connecting surface or touch the screw holes. When picking and placing the bolster, your fingers should be placed on both sides of the bolster.
However, Yueluo still feels that there should be room for improvement for the screw improvement and screw that integrates stability, labor, fast and multi-function in the above two cases; for example, No. 556784 screw improvement Although the rod has the function of cutting and collecting chips, when the screw starts to screw into the object such as wood, it is hindered by the hardness of the object's tissue, so the staff still needs to exert considerable force, resulting in the lock. In the solid operation, there is still a lack of difficulty in screwing in operation; another example, new cases such as No. 289408 screw that integrates locking, stability, labor, fast and multi-function, although the rod has the structural function of cutting and chip removal, it is The rod part is screwed into the middle section to the rear section of the object. Since the debris cannot be discharged, the rod part pushes the outer part of the object to the surrounding tissue of the object, so that the object expands outwards and even seriously damages the appearance of the object.
In the prior art, after the screw is screwed into the workpiece, rust inhibitor is dripped on the edge of the screw to prevent rust in the later stage, but this traditional dripping method of rust inhibitor often produces rust inhibitor during the dripping process. Difficult to penetrate, or the problem that the anti-rust oil cannot penetrate due to the tight contact between the screw thread and the thread groove. In terms of material saving, the traditional anti-rust of screws often causes a lot of waste of anti-rust agent, and cannot achieve a good anti-rust effect of screws.
As one of the indispensable parts in automobiles, the main function of the screw is to fix the parts with through holes and the parts with screw holes together. The existing automobile screws include a screw rod and a head, and the thread pitches on the screw rod are equal. , When in use, directly screw the screw into the screw hole, so as to connect and fix the two parts, this connection method, however, when the screw has different thread spacing or part of the thread is damaged, the thread cannot be repaired and replaced. Then the whole screw will be scrapped.
At present, injection molding screws are widely used in various electronic and automotive components, including a body, the middle of which is provided with a through hole 3, the body head 1 has a hexagonal cross-section, and the tail 2 is provided with screw teeth. When in use, the middle through hole 3 of the body will first put the wire harness, and then fix it by injection molding from the head I, and the threads of the tail 7 should be connected and installed with other components. Because the head I of the main body is hexagonal, the torque provided after injection molding is insufficient. Therefore, after the external thread is installed and connected with other components, the head is prone to slip, the installation is not reliable, and there is no push-pull force, resulting in product failure and increased safety hazards.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB802.4 hexagonal cap nuts, anchored flat head hexagonal rivet nuts, hexagonal head screw screws, standard stainless steel bolts and other products, we can provide You have the right fastener solution for you.
