Service HotlineIt can be seen from the extrusion process that the screw works under high temperature, certain corrosion, strong wear and high torque. Therefore, the screw must: 1) High temperature resistance, no deformation under high temperature; 2) Wear resistance, long life; 3 ) Corrosion resistance, the material is corrosive; 4) High strength, can withstand large torque, high speed; 5) Good cutting performance; 6) After heat treatment, the residual stress is small, and the thermal deformation is small. [1]
In real life, rivet nuts are used. With different specifications and different uses, many people are familiar with this tool but don't know how to use it properly. In fact, rivet nut tools have manual and transmission, and now are rarely used for manual. If you choose to use electric rivet nuts in order to improve production efficiency, which of the two is more widely used? The following describes the use of electric rivet nuts and manual nuts. How to use the manual rivet nut tool: Insert the rivet nut into the drilled installation hole with a rivet mother tool to fix the rivet nut. (1) Screw the rivet nut onto the rivet nut tool 2) Use the rivet nut tool to insert the rivet nut into the drilled mounting hole. (3) Tighten the nut, and press the handles on both sides of the rivet nut tool to the direction of the middle round rod. You can only press it hard. Therefore, this pressure must be in place. It is forbidden to repeatedly squeeze the handles on both sides to damage the nut. Fastening thread in the form of inside. (4) The rivet nut tool is separated from the rivet nut: just loosen the ball head in the picture, and the tool will be separated from the nut after completely loosening.
The material of the combination screw is divided into iron and stainless steel. The iron ones are made of different iron screw wires. Generally, the wire of the combination screw is 1010, 1018, 10B21 and so on. 10B21 is used to make 8.8 grade combination screws. Like 8.8 grade hexagon socket head combination screws, 10B21 wire is often used. When done, go to heat treatment. After heat treatment, remove hydrogen and electroplating. This is to prevent the spring washer of the socket head cap screw from breaking. Stainless steel combination screws, in the combination screw market, generally refer to stainless steel SUS304 combination screws. 201 combination screws generally do very little. Few combination screw manufacturers produce 201 combination screws. Because the hardness of the screw wire of stainless steel 201 is not well controlled, it is easy to produce cracks.
Most of the electroplating used for rivet nuts on the market is environmental protection blue zinc, because the salt spray test time of environmental protection blue zinc can reach 72 hours, that is, three days. This kind of electroplating has a longer salt spray resistance time. In fact, for example, for electroplating white nickel, the salt spray time of white nickel is relatively short, and it usually rusts in a few hours, which is less than 10 hours. However, some can be oiled for electroplating white nickel, and the salt spray time of the rivet nut after oiling can be longer. S series rivet nuts are made of free-cutting iron, which is treated after heat treatment. CLS series rivet nuts are made of easy-to-cut stainless steel. The hardness of low-carbon steel plates without surface treatment must be less than 70RB, and the hardness of stainless steel plates must be less than 80RB.
Electrical contact element is a kind of low-voltage electrical products and household electrical products widely used in switches, relays, thermostats, circuit breakers, contactors, controllers, timers, etc. There are mainly three types of electrical contact elements. 1. Riveting parts , riveting the rivet on the copper piece; 2. Welding piece, welding the sheet contact on the copper piece; 3. Stamping piece, punching the composite tape into components. Existing rivet contacts on the market at present are usually all made of precious metals, such as a simple metal matrix such as gold or silver. Its electrical contact performance is limited by a single metal material, and its electrical contact performance is poor; and due to certain requirements for metal purity in production, production efficiency is low, and production costs are high, resulting in the production of products that cannot be sold on a large scale in the market. and application.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: galvanized square nuts, green high temperature resistant silicone rings, pressure riveting parts pressure riveting round nuts, butterfly screws and bolts and other products, we can help you Provide the right fastener solution for you.
