Service Hotlineconcealed screw fastener includes a washer, a screw and a shield, one end of the screw is provided with an end cap, the screw penetrates the washer and the end cap is supported on the washer, and the shield covers the end of the screw The cap is peripheral and connected to the gasket. When in use, firstly pass the screw through the washer and then drive it into the screw hole of the connected piece, and then cover the shield on the outer circumference of the end cap of the screw and connect it with the washer.
The core rivet is another type of single-sided riveting. When riveting, the head of the rivet is hit with a hammer to expose the core, so that it is flush with the end face of the nail head, that is, the riveting operation is completed, which is very convenient, especially suitable for inconvenient Riveting occasions using ordinary rivets (which must be riveted from both sides) or blind rivets (lack of a rivet gun). Usually use flat head rivets, countersunk head rivets are suitable for occasions where smooth riveting is required on the surface. Some rivets can also be matched with clothing, becoming a popular element today, mostly the representative of punk style. In addition, there are paired rivets, which are special. Divided into two parts, the thicker section of the rod with a cap has a hole in the center, and the other section of the rod with a cap is an interference fit. When riveting, drive the thin rod into the thick rod.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
Drilling screw is a new invention of people in recent years. A screw is a common term for fasteners, an everyday colloquial language. The tail of the drill tail screw is in the shape of a drill tail or a pointed tail, and no auxiliary processing is required. Drilling, tapping and locking can be directly carried out on the setting material and basic material, which greatly saves construction time. Compared with ordinary screws, its toughness and pull-out force and maintenance force are high, and it will not loosen for a long time after combination. It is easy to use safe drilling and tapping in one operation. Drill tail screw Drill tail screw use: It is a kind of screw, mainly used in the fixing of color steel tiles of steel structures, and can also be used for thin plate fixing of simple buildings. It cannot be used for metal-to-metal bonding. Materials and models The materials are iron and stainless steel, of which stainless steel is divided into various materials. Models are: Φ4.2/ Φ4.8/ Φ5.5/ Φ6.3mm, the specific length can be agreed upon request. According to the different drill tails, it can be divided into: round head rice / cross / plum blossom, countersunk head (flat head) / rice seed / cross / plum blossom, hexagonal washer, round head washer (big flat head), horn head, etc.
(+): Cross slot (-): Slotted slot (T): Chrysanthemum slot (H): Hexagon socket (PZ): Bevel slot (+-): +- slot (Y): Y-shaped slot (H) : H-groove (L): Back-stop tooth (WIS): Single-moving spring washer (WIF): Single-moving flat washer (WIT): Single-moving external tooth washer (W2SF): Double-moving flat washer (W=6mm ): Washer outer diameter equal to 6mm (SUS): Stainless steel (Cu): Brass (Br): Red copper (8.8): Grade 8.8 screw (10.9): Grade 10.9 screw (12.9): Grade 12.9 screw (R): Other Notes
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: swing ring screws, outer carbon steel galvanized screws, hexagonal flange lock nuts, fastening fastener bolts and other products, we can provide You have the right fastener solution for you.
