Service HotlineThe flat washer is mainly used to reduce the pressure. When some parts are tightened with a large axial force, it is easy to press the washer into a dish shape. At this time, it can be solved by changing the material and increasing the hardness.
In order to overcome the above problems, Guangdong Yueluo Hardware Industry Co., Ltd. provides a screw that can be quickly installed and removed. Using the principle of lever, press the handle downward, and the screw can form a backward force through the connecting piece. Press the screw and nut tightly; lift the handle, the screw forms a forward force, and the screw can be removed. Thus, the time and manpower for screwing during installation and disassembly are reduced. The solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is that the entire screw includes a screw rod, a nut, a connecting piece, a circlip, a positioning pin, a small shaft, a fixed piece, a base, and a handle; the screw is connected by the small shaft at the upper end. At the upper end of the connecting piece, the handle is connected to the lower end of the connecting piece, and the front end of the handle is connected to the base fixing piece through a positioning pin. There are gaps at both ends of the small shaft, and the small shaft is installed through the circlip. The front end of the handle can only be rotated on the positioning pin. Due to the lever principle, when the handle is pressed down, it will drive the screw at the front end of the connecting piece, so that the screw generates a backward force and tightens the screw and the nut. On the contrary, when the handle is pulled up, the screw generates a forward force, so that the screw can be easily removed. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is that the quick-opening screw saves the time and labor of repeatedly twisting the nut during installation and disassembly. The installation and removal process is simple.
The blind rivet is realized by pulling the core head. With the help of a force from the inside to the outside, under the action of the unidirectional pulling force, the pulling screw is pulled upwards, which causes the outer collar material to expand and deform, resulting in a sexual tightening force. , After the riveting is completed, the tension screw in the middle part breaks and falls out. Since a large pulling force is required to cause the rivet to expand and deform, the tensile screw is longer and accounts for about 60-80% of the total length of the rivet. At the same time, due to the limitation of the deformation mode, it is difficult for the blind rivet to be made into a hexagonal structure like a rivet nut, so the torsion resistance of its connection is low.
Shaft retaining ring (hereinafter referred to as retaining ring) is a very common part and is widely used in shaft parts. The existing solution for pressing the retaining ring is: place the retaining ring sleeve in the chamfering section or the guiding section of the shaft head, and then use an indenter whose inner hole diameter is larger than the diameter of the shaft head to press the retaining ring into the groove, and then press the retaining ring into the groove through the shaft head. The retaining ring is combined with the slot to prevent the indenter from continuing to move downward.
Bolt: A type of fastener consisting of a head and a screw (a cylinder with an external thread), which needs to be matched with a nut to fasten and connect two parts with through holes. This form of connection is called a bolted connection. If the nut is unscrewed from the bolt, the two parts can be separated, so the bolt connection is a detachable connection. [1] Stud: A type of fastener that has no head and only has external threads on both ends. When connecting, one end of it must be screwed into the part with the internal threaded hole, the other end must pass through the part with the through hole, and then the nut must be screwed on, even if the two parts are tightly connected as a whole. This form of connection is called a stud connection, which is also a detachable connection. It is mainly used for occasions where one of the connected parts is thick, requires a compact structure, or is not suitable for bolt connection due to frequent disassembly. [1] Screw: It is also a type of fastener consisting of a head and a screw. It can be divided into three categories according to the purpose: machine screws, set screws and special-purpose screws. Machine screws are mainly used for a fastened connection between a part with a fixed threaded hole and a part with a through hole, without the need for nut matching (this connection form is called screw connection, which is also a detachable connection; it can also be Cooperate with the nut, it is used for the fast connection between two parts with through holes.) The set screw is mainly used to fix the relative position between the two parts. Special purpose screws, such as eyebolts, are used for hoisting parts. [1] Nuts: with internal threaded holes, generally in the shape of a flat hexagonal column, but also in a flat square column or flat cylindrical shape, with bolts, studs or machine screws, used to fasten and connect two parts, make it a whole. [1] 5. Self-tapping screw: Similar to machine screw, but the thread on the screw is a special thread for self-tapping screw. It is used to fasten and connect two thin metal components to make them a whole. Small holes need to be made in advance on the components. Due to the high hardness of this kind of screw, it can be directly screwed into the hole of the component, so that the Forming a corresponding internal thread [1] 6. Wood screw: It is also similar to a machine screw, but the thread on the screw is a special thread for wood screws, which can be directly screwed into wooden components (or parts) to connect a band through The metal (or non-metallic) part of the hole is fastened to a wooden member. This connection is also a detachable connection. [1] 7. Washers: A type of fastener with an oblate annular shape. It is placed between the supporting surface of the bolt, screw or nut and the surface of the connecting part, which increases the contact surface area of the connected parts, reduces the pressure per unit area and protects the surface of the connected parts from damage; another type of elastic washer, It can also play a role in preventing the nut from loosening. [1] 8. Retaining ring: It is installed in the shaft groove or shaft hole groove of the machine and equipment, and plays the role of preventing the parts on the shaft or the hole from moving left and right. [1] 9. Pins: mainly used for positioning the left and right parts, and some are also used for connecting parts, fixing parts, transmitting power or locking fasteners. [1] 10. Rivet: A type of fastener consisting of a head and a shank, which is used to fasten and connect two parts (or components) with holes to make them a whole. This form of connection is called rivet connection, or riveting for short. It is a non-removable link. Because if the two parts joined together are separated, the rivets on the parts must be broken. [1] 11. Components and connection pairs: Assemblies are a type of fasteners supplied in combination, such as a combination of a certain machine screw (or bolt, self-supplied screw) and a flat washer (or spring washer, lock washer); Connection pair refers to a type of fastener that is supplied by a combination of special bolts, nuts and washers, such as high-strength hexagon head bolt connection pairs for steel structures. [1] 12. Welding nail: a heterogeneous fastener composed of a nail rod and a nail head (or no nail head), which is fixed to a part (or component) by welding, so as to be connected with other parts. .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head hexagonal rivet nuts, handle screws, solid aluminum rivets, round head Phillips screws and bolts and other products, we can provide you with fastening suitable for you piece solution.
