Service HotlineIn all kinds of machines and equipment, the various parts are fixed and assembled by bolts and nuts. However, after the machine and equipment are used for a period of time, the bolts and nuts will become loose, which will bring great safety hazards to the use of the machine and equipment. For this reason, when bolts and nuts are used for connection, a spring washer is installed between the nut and the connected part. The spring washer is in the shape of a circular ring, and the ring is not closed, and is sleeved on the bolt. The addition of the spring washer has a certain anti-loosening effect, but it can only prevent the nut from rotating relative to the bolt. In the case of large vibration of the machine, the bolt will rotate relative to the connected part.
In the existing life, repair parts are often used to repair the cassettes with damaged screw holes, and the screw holes on the repair parts are used instead of the original damaged cassette screw holes. However, in the prior art (application number: 201520948368.3), the restoration is fixed by rotating the support of the restoration, which is often inconvenient due to the small space of the cassette. In addition, the set screw in the prior art mainly fastens the object through the end of the screw without threaded holes, which makes it difficult to install external screws. Based on this, a method of extruding the support through a set screw with screw installation holes and tightening the repair piece, and then installing the screw on the set screw, will facilitate the quick installation and use of the repair piece.
Spring mattresses and spring seat cushions are modern and commonly used furniture products with better performance, and their cushion cores are composed of springs. It makes full use of the advantages of good spring elasticity, good support, strong air permeability and durability. The traditional spring pad is a spring with a thicker wire diameter, which is connected and fixed by steel wires, and has high hardness. Most of the elders of the older generation often use linked spring beds, but if they sleep in a fixed position for a long time or are accustomed to sitting on the side and corners of the bed, or flip the mattress irregularly, it is easy to cause depression and elastic fatigue.
In the riveting operation, the rivet used is composed of a mandrel and a deformed collar. When in use, a through hole is drilled on the two components to be connected, and then the head of the rivet is passed through the through hole and clamped by a rivet. The tail of the rivet will break the rivet, the head of the rivet and the deformed collar remain in the through hole, and the whole riveting process is completed. The existing pull rivets have the following shortcomings: first, the parts where the pull rivet and the two components are connected cannot be completely and tightly fitted, which meets the requirements of non-sealing for parts that have waterproof and leak-proof requirements; second, the existing pull rivets The separation groove of the rivet mandrel is close to its head. When the mandrel is broken by the rivet during the riveting process, basically only the head of the mandrel remains in the deformation collar, and the connection of the two components depends on the deformation of the collar. Under the action of compressive stress, the inside of the deformed collar becomes hollow due to the breaking of the mandrel, and cannot bear large shear stress.
The machinery industry is one of the main users of fasteners. Due to China's late understanding of the important position of mechanical basic parts in the machinery industry and a long-term lack of investment, the entire industry has a poor foundation, weak foundation and weak strength. Especially with the improvement of the level of the main engine in China, the bottleneck phenomenon that the mechanical basic parts lag behind the main engine has become increasingly apparent. Today, although the state has given certain support in technology introduction, technological transformation, scientific research and development, etc., there is still a big gap compared with the current market demand and foreign levels. Unstable quality, high early failure rate and poor reliability. Fasteners are the main basic products in the machinery industry, and the development of the machinery industry also puts forward higher requirements for fastener products. Domestic ordinary standard fasteners have always been in oversupply, while high-end fasteners (high temperature, special-shaped, titanium-plastic composite, special performance and other fasteners) are in short supply, and they also rely on imports. The State Machinery Bureau lists ordinary standard fasteners as restricted development products, and high-strength special-shaped fasteners as currently encouraged development products. With the improvement of the country's industrialization level and technological progress, the use of high-strength fasteners has gradually increased.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: star handle screws, bald head non-knurled screws, silicone gaskets, hot-dip galvanized bolts and other products, we can provide you with suitable fasteners. Firmware Solutions.
