Service HotlineM4 grounding screw used to fix the grounding wire on household appliances and other equipment, the stud is cylindrical, and the thread is perpendicular to the end (section) surface. However, the screw holes on the equipment all have tapping guide grooves for sinking and guiding due to the manufacturing process requirements. When fixing the ground wire, if the screw is not positioned accurately (the screw is inclined), the screw is pressed down hard, which is easy to cause the screw and the screw. The screw hole bites the teeth, and after biting the teeth, it is easy to cause the screw to loosen or fall off, posing a safety hazard.
Blind rivets (blind rivets) --------- rivet body (rivet body) mandrel (rivet stem or rivet mandrel). It is a type of rivet for single-sided riveting, but it must be riveted with a special tool - a rivet gun (manual, electric, pneumatic). When riveting, the rivet core is pulled by a special rivet gun to expand the rivet body and play a riveting role. This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets (riveting from both sides), so it is widely used in construction, automobiles , ships, aircraft, machinery, electrical appliances, furniture and other products. Among them, the open-type oblate head blind rivets are the most widely used, the countersunk head blind rivets are suitable for riveting occasions where the surface needs to be smooth, and the closed blind rivets are suitable for riveting occasions that require high load and certain sealing performance.
(1) The screw-in performance test is to screw the self-tapping locking screw sample into the test plate until one complete thread completely passes the test without breaking. (2) The destructive torque test is to clamp the stem of the self-tapping locking screw specimen in a thread mold or other device that matches the screw thread, and uses a calibrated torque-measuring device to measure the screw. Torque is applied until fracture, which should not occur in the clamped threaded portion. (3) Carry out a tensile test on the screw sample to check the minimum tensile load for failure. The fracture should be within the length of the rod or the unthreaded thread, and should not occur at the junction of the nail head and the rod. Before the sample breaks, it should be It can reach the minimum tensile load specified by the corresponding performance class. (4) Hydrogen embrittlement is a problem that must be strictly paid attention to in the surface treatment process of self-tapping locking screws. In the pickling process, the screw is stirred in dilute hydrochloric acid, and the amount of hydrogen absorbed by the pickling steel increases linearly with the square root of time and reaches the saturation value. Less than 100%, a large number of hydrogen atoms will be produced, which will be attached to the surface of the screw, resulting in hydrogen infiltration, and the steel will become brittle due to the absorption of hydrogen. The self-tapping locking screw takes 6~8h to drive hydrogen, and the temperature is 160~200℃ (phosphating) and 200~240℃ (electroplating). However, in the production process, the hydrogen drive time should be determined according to many production conditions such as core hardness, surface roughness, electroplating time, coating thickness, pickling time, and acid concentration. It is best to do it before passivation and just after electroplating.
The technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve the problems of the prior art is: a patch nut, which is characterized in that it includes a nut body, and the nut body has a welding end face, and the edge of the welding end face forms a The serrated teeth protruding outwards of the ring.
Related Specifications of Automobile Welding Nuts (Square Nuts) Serial Number Standard Number Name (English) Name (Chinese) Remarks 1 MS440014 NUT,WELD Welding Square Nut M8 2 MS440013 NUT,WELD (6) Welding Square Nut M6 3 MF445605 NUT,WELD (10 ) welding square nut M10 4 MU442002 NUT,WELD welding square nut M6 parking brake handle 5 MB077464 NUT,WELD welding square nut for seat belt welding square nut 6 MB040348 BOLT WELD (10X22) welding bolt M10×22, bearing surface 7 MF198353 BOLT,WELD (6X14) Weld bolt M6×14, end face 8 MR236366 NUT (12) Nut M12 Suspended trailing arm mount 9 MS440015 NUT,WELD (10) Weld square nut M10 10 PW832525 BOLD WELD 7/16 UNF Weld bolt 7/16 For seat belt, bearing surface 11 MB528563 STUD,WELD Welding stud M6×20 12 MS440066 NUT,WELD (5/16=18UNC) Welding square nut 5/16 Child safety system 13 MS440018 NUT, WELD (6) Welding square nut M6 14 MF198375 BOLT,WELD (8X30) Welding stud M8×30 15 MF198038 BOLT, WELD (6X25) Welding bolt M6×25, bearing surface 16 MR236467 NUT (12) Welding square nut M12, for engine mount 17 MF140024 BOLT, FLANGE (8X18) Hexagon flange bolt without 3D 19 MF198036 BOLT,WELD (6X20) Weld stud M6×20 20 MF198034 BOLT,WELD (6X16) Weld bolt M6×16, bearing face 21 MS440012 NUT,WELD (5) Weld Square Nut M5 22 MB343340 BOLT,WELD (8X26) Welding Bolt M8×26, Bearing Surface 23 MB138471 STUD,WELD Welding Stud M8×46, Bearing Surface 24 MS190066 BOLT,WELD (8X16) Welding Bolt M8×16, Bearing Surface, NO 3D 25 MS240145 BOLT,WASHER ASSEMBLED (8X20) BOLT AND WASHER ASSEMBLY NO 3D 26 MB281149 NUT,WELD(6) WELD BOLTS M8, NO THREADS REQUIRED FOR BEARING 27 MF445603 NUT,WELD (6) Welded square nut M6 Reinforcing plate for rear door lock 28 MS190068 BOLT,WELD (8X20) Welded bolt M8×20, bearing surface 29 MU431507 NUT,WELD Welded square nut M8 for door hinge installation 30 MS240121 BOLT,WASHER ASSEMBLED (6X16) Bolt and washer assembly M8 for fuel filler cap 31 MS100221 BOLT,FLANGE (6X12) Flange face bolt M6 for fender mounting 32 MB344675 STUD,WELD Weld stud M6×10
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: extended black screw, DIN137A, main board isolation column, spring washer and other products, we can provide you with suitable fastener solutions for you .
