Service HotlineThe advantages of the pressure riveting nut: 1. The length guarantee of the distance range is realized, which greatly simplifies the assembly process and speeds up the production progress of the assembled spacing panel and accessories; 2. The back of the plate is completely embedded and flat, while ensuring the head of the nut column The plane is smooth with the plate; 3. The raw material is free-cutting iron or free-cutting stainless steel; the technical guide for the application of the pressure riveting standoff: 1. When selecting the standoff, it must be based on the thickness of the plate used, the exact size range, and the hardness of the low-carbon steel plate must be less than 70RB, the hardness of stainless steel plate must be less than 80RB. 2. The surface of free-cutting iron is treated, and the stainless steel maintains its original color. Users can order according to the model and specifications in the table according to their needs, or they can also make special orders according to their needs. 3. The hole size of the plate must be processed according to the tolerance size of 0-+0.075mm, and punching is recommended. 4. The installation must be realized by press riveting operation, and it must not be knocked in by impact. 5. When the material is stainless steel, the tail number should be marked with S. 6. The end face of the nut column is represented by C. 7. The length of the through-hole nut column is full wire below 10mm. If it is above 10mm, it can be reamed on the hexagonal end face (type I) or the round end face (type II).
In the prior art, the beams used for installing the curtain wall are mainly divided into two types: closed-cavity structure and open structure, and angle aluminum connection is mainly used for the connection between the beam and the column. As far as the beam of the closed-cavity structure is concerned, after the angle aluminum is used to connect, there are open bolts on both ends of the upper surface of the beam, and the aesthetic performance is extremely poor. As far as the beam of the open structure is concerned, in the actual connection, first fix one corner of the angle aluminum to the beam, and then connect the other corner of the angle aluminum to the column; due to the limited operating space in the beam of the open structure, the angle aluminum is not It is easy and accurate to install, and it takes a lot of time to install; and when the curtain wall panel is heavy, the beam will be twisted, causing the gusset of the opening part of the beam to fall. In addition, due to the limitation of the opening structure itself (an additional gusset or clasp), the aluminum content of the beam is relatively heavy, and the manufacturing cost is high.
Type 1 nut refers to an ordinary hexagonal nut with a nominal height of m ≥ 0.8D. Its type and size should meet the requirements of GB/T6170; while the height of type 2 nut is higher than that of type 1 nut, its type and size should comply with GB/T6170. T6175. There are two purposes to increase the type 2 nut: one is to obtain a relatively inexpensive nut that does not require heat treatment by increasing the height of the nut. Because D≤M16 grade 8 type 1 nuts do not need heat treatment, among grade 8 nuts, only the specifications of D>M16~39 use type 2 nuts. Obviously, type 1 nuts that do not need heat treatment cannot reach grade 9 nuts. Mechanical property requirements. Another purpose of specifying Type 2 nuts is to obtain a more ductile grade 12 nut. As the height of the nut increases, the guaranteed stress index can be achieved at a lower quenching and tempering hardness, so the toughness of the nut is increased. Classified by tooth spacing: standard teeth, regular teeth, fine teeth, very fine teeth and cross teeth. Classification by material: stainless steel hexagon nuts and carbon steel hexagon nuts, copper hexagon nuts, iron hexagon nuts. Classification by thickness: hexagonal thick nuts and hexagonal thin nuts. Classification by usage: hot melt copper nut, hot pressed copper nut, embedded copper nut and ultrasonic copper nut
hand screw is a screw with a plastic head, and the user fixes the hand screw by turning the plastic head by hand. At present, a hand-tight screw is disclosed in the market publication number CN202203253U, which includes a plastic head and a screw rod, the plastic head and the screw rod are connected together, and the height of the plastic head is higher than that of ordinary screws, and the height is 3 cm. The screw of the hand screw is fixed in the plastic head by glue. After a period of use, the aging of the glue leads to the loosening of the screw and the plastic head. When the plastic head is stressed, the screw rod comes out of the plastic head, which affects the normal use of the hand screw.
The existing nut fasteners are generally used to fix the bolts to fix the devices with holes. However, during the operation of most devices, the bolts and nuts are easily loosened and separated due to mechanical vibration, causing long-term vibration. It will cause the nut to separate from the bolt, affecting the safety and stability of the device during operation. At the same time, in the connection between the bolt and the nut for a long time, the external dust easily enters the connection, resulting in the accumulation of dust, making the bolt and nut difficult to disassemble. Affect the use of fasteners.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: DIN938 unequal length bolts, metric half-thread bolts, PC board spacer studs, carriage square neck bolts and other products, we can provide you with products suitable for you fastener solutions.
