Service HotlineIn CN203807560, nails and bolts are used to connect the plates, but the heads of the nails and the bolts are enlarged ends that are wider than the rods, and the heads of the nails and the bolts cannot penetrate into the interior of the door body, so in terms of appearance, the more More nails and bolts will leave more spots on the surface of the door that are not suitable for the door itself. In the prior art, the treatment method for these spots is generally to paint with paint, which can only make the door panel consistent with the head of the nail and the bolt in color, but cannot change the shape of the head of the nail and the bolt, and the appearance is still good. Obvious spots were noticed, which made the door panels connected by nails and bolts to the panels, which could not be used as door panels for household doors.
Guangdong Yueluo Hardware Industry Co., Ltd. is a screwing fixture, including a bottom plate, a bearing seat and a hydraulic press are respectively installed on both sides of the top of the bottom plate, a bearing is installed inside the bearing seat, and the inner ring of the bearing is connected to the support The bottom end of the vertical rod is snap-connected, the top end of the supporting vertical rod is fixedly connected to the supporting horizontal rod through an adjusting screw, the bottom end of the supporting horizontal rod is provided with a chute, and the inside of the chute is connected by sliding The slider is fixedly connected with the electric batch, the hydraulic press is connected with the fixed seat through the hydraulic rod, the top of the fixed seat is fixedly connected with the screw positioning plate through two fixed blocks, and the opposite side of the two fixed blocks is provided with Clamping mechanism for clamping workpieces.
Two combination screws are also called two combination screws. As the name suggests, it consists of a screw with a spring washer or only a flat washer. After the thread rolling, the two components are combined together. Two combination screws are available in iron and stainless steel. For iron, there are screw materials such as screw wire 1010, 1018, 10B21, etc. The general iron pier needs to be electroplated, and electroplating is divided into environmental protection and ordinary. For example, there are environmentally friendly color zinc, environmentally friendly blue zinc, white zinc, color zinc, white nickel and other electroplating. Stainless steel two combination screws. The material is stainless steel 304.
When the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
Blind rivets are a type of rivets for single-sided riveting, but they must be riveted with a special tool - a rivet gun (manual, electric, pneumatic). This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets (which must be riveted from both sides), so it is widely used in construction, automobiles, ships, aircraft, machinery, electrical appliances, furniture and other products. Among them, the open type oblate head blind rivets are the most widely used, the countersunk head blind rivets are suitable for riveting occasions that require smooth performance, and the closed blind rivets are suitable for riveting occasions that require higher load and certain sealing performance.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: equal-length double-head stud screws, component package double-pass isolation column nuts, brass photo album accessories, DIN25201 and other products, we can provide You have the right fastener solution for you.
