Service HotlineStainless steel bolts refer to bolts made of stainless steel, including stainless steel SUS201 bolts, stainless steel SUS304 bolts, stainless steel SUS316 bolts, and stainless steel SUS316L bolts. The performance grades of stainless steel bolts, studs and studs are divided into 10 grades: from 3.6 to 12.9. The number before the decimal point represents 1/100 of the tensile strength limit of the material, and the number after the decimal point represents 10 times the ratio of the yield limit to the tensile strength limit of the material.
Screw, some people call it screw (screw), screw (screw rod). In fact, the screw is a general term, and the screw and the screw rod are different from each other. Screws are generally called wood screws; they are the ones with a pointed end at the front and a larger pitch. They are generally used to fasten wooden and plastic parts. The screw rod is a machine screw (machine screw), which is the kind of flat head at the front end. The pitch is small and uniform. It is generally used to fasten metal and machine parts.
(1) The screw-in performance test is to screw the self-tapping locking screw sample into the test plate until one complete thread completely passes the test without breaking. (2) The destructive torque test is to clamp the stem of the self-tapping locking screw specimen in a thread mold or other device that matches the screw thread, and uses a calibrated torque-measuring device to measure the screw. Torque is applied until fracture, which should not occur in the clamped threaded portion. (3) Carry out a tensile test on the screw sample to check the minimum tensile load for failure. The fracture should be within the length of the rod or the unthreaded thread, and should not occur at the junction of the nail head and the rod. Before the sample breaks, it should be It can reach the minimum tensile load specified by the corresponding performance class. (4) Hydrogen embrittlement is a problem that must be strictly paid attention to in the surface treatment process of self-tapping locking screws. In the pickling process, the screw is stirred in dilute hydrochloric acid, and the amount of hydrogen absorbed by the pickling steel increases linearly with the square root of time and reaches the saturation value. Less than 100%, a large number of hydrogen atoms will be produced, which will be attached to the surface of the screw, resulting in hydrogen infiltration, and the steel will become brittle due to the absorption of hydrogen. The self-tapping locking screw takes 6~8h to drive hydrogen, and the temperature is 160~200℃ (phosphating) and 200~240℃ (electroplating). However, in the production process, the hydrogen drive time should be determined according to many production conditions such as core hardness, surface roughness, electroplating time, coating thickness, pickling time, and acid concentration. It is best to do it before passivation and just after electroplating.
Related Specifications of Automobile Welding Nuts (Square Nuts) Serial Number Standard Number Name (English) Name (Chinese) Remarks 1 MS440014 NUT,WELD Welding Square Nut M8 2 MS440013 NUT,WELD (6) Welding Square Nut M6 3 MF445605 NUT,WELD (10 ) welding square nut M10 4 MU442002 NUT,WELD welding square nut M6 parking brake handle 5 MB077464 NUT,WELD welding square nut for seat belt welding square nut 6 MB040348 BOLT WELD (10X22) welding bolt M10×22, bearing surface 7 MF198353 BOLT,WELD (6X14) Weld bolt M6×14, end face 8 MR236366 NUT (12) Nut M12 Suspended trailing arm mount 9 MS440015 NUT,WELD (10) Weld square nut M10 10 PW832525 BOLD WELD 7/16 UNF Weld bolt 7/16 For seat belt, bearing surface 11 MB528563 STUD,WELD Welding stud M6×20 12 MS440066 NUT,WELD (5/16=18UNC) Welding square nut 5/16 Child safety system 13 MS440018 NUT, WELD (6) Welding square nut M6 14 MF198375 BOLT,WELD (8X30) Welding stud M8×30 15 MF198038 BOLT, WELD (6X25) Welding bolt M6×25, bearing surface 16 MR236467 NUT (12) Welding square nut M12, for engine mount 17 MF140024 BOLT, FLANGE (8X18) Hexagon flange bolt without 3D 19 MF198036 BOLT,WELD (6X20) Weld stud M6×20 20 MF198034 BOLT,WELD (6X16) Weld bolt M6×16, bearing face 21 MS440012 NUT,WELD (5) Weld Square Nut M5 22 MB343340 BOLT,WELD (8X26) Welding Bolt M8×26, Bearing Surface 23 MB138471 STUD,WELD Welding Stud M8×46, Bearing Surface 24 MS190066 BOLT,WELD (8X16) Welding Bolt M8×16, Bearing Surface, NO 3D 25 MS240145 BOLT,WASHER ASSEMBLED (8X20) BOLT AND WASHER ASSEMBLY NO 3D 26 MB281149 NUT,WELD(6) WELD BOLTS M8, NO THREADS REQUIRED FOR BEARING 27 MF445603 NUT,WELD (6) Welded square nut M6 Reinforcing plate for rear door lock 28 MS190068 BOLT,WELD (8X20) Welded bolt M8×20, bearing surface 29 MU431507 NUT,WELD Welded square nut M8 for door hinge installation 30 MS240121 BOLT,WASHER ASSEMBLED (6X16) Bolt and washer assembly M8 for fuel filler cap 31 MS100221 BOLT,FLANGE (6X12) Flange face bolt M6 for fender mounting 32 MB344675 STUD,WELD Weld stud M6×10
① Nominal thread outer diameter (thread specification): divided into metric system and inch system. Metric thread → common specifications are 2; 2.3; 2.5; 2.6; 2.9; 3; 3.1; 3.5; 4; 4.2; 4.5; The unit is mm (millimeters). Inch thread→ Common specifications are 2#;4#;6#;8#;10#;12#;1/4;7/32;5/16;3/8;1/2 ;9/16;3/ 4. The unit is in (inches). ② Number of teeth/pitch: Definition of number of teeth → the number of teeth lines in one inch (25.4mm) length. Pitch Definition → Distance value between two adjacent threads. Conversion of number of teeth and pitch of teeth → pitch of teeth = 1 inch/number of teeth ③Nominal length: divided into metric system and inch system. Metric Nominal Length → Common values are 5, 6, 6.5, 7, 8, 9, 9.5, 10, 11, 12, 13, 14, 15, 16, 18, 19, 20, 21, 25, 28, 30, 31 , 32, 35, 40, 42, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120. The unit is mm (millimeters). Imperial Nominal Length → Common values are 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, 1, 2, 3. Units: in (inches). ④Head type: use letters to indicate the type of head type, please refer to the previous classification of commonly used screw head types. ⑤Tooth type/tail type: Use letters to indicate the type of tooth type/tail type, please refer to the previous Commonly used screw thread/tail type classification. ⑥Groove type: Please refer to the previous section Category of common screw groove types of our company. Cross-slotted or non-slotted (such as punched hexagon head screws) do not need to be marked here, and other groove types need to be described in words. ⑦Special labeling: In general, no labeling is required. When expressing its characteristics, it is described in words at this position. For example: the specification name of the screw is described as 4-0.7x70PM±tooth length 35, which means 4 is the nominal diameter of the screw thread, 0.7 is the pitch, 70 is the nominal length of the screw, and P means its The head type is a pan head, M means its tooth type/tail type is a wire thread type, ± means its groove type is ± groove and can also be expressed by plus or minus groove. Tooth length 35 is special Mark, specify the thread length value of this screw.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: extended full-thread screws, flat washers combination, nylon external screws, flat washers and other products, we can provide you with products suitable for you fastener solutions.
