Service HotlineTraditionally, the pressure rivets on the product are all beaten by hand by workers, resulting in high scrap rate and low efficiency, and this rivet is not a traditional rivet, so it is difficult to locate and requires high pressure. The rivets are thin, and the pressure is too large to cause deformation of the rivets. If the pressure is too small, it cannot be riveted. Without special positioning and tooling, it cannot be riveted on the riveting machine. The quality of the products produced in this way is difficult to guarantee, and the quality levels of the products in the same batch are uneven. Affect delivery time.
GBT 3098.19-2004 blind rivets in my country are divided into: GB/T12615 closed oblate head blind rivets; GB/T12616 closed countersunk head blind rivets; GB/T 12617 open type countersunk head blind rivets; T 12618 Open-type oblate head blind rivets; the international standard is DIN7337; there are 1990 versions and 2004. The 2006 version is mainly the 2006 version.
The two combination screws are classified according to the national standard, including GB9074.2, GB9074.3, GB9074.5, etc. GB9074.3 refers to a two-component combination of a cross pan head screw and a foreign lock washer.
In many national standards, there will be a division of intensity levels. Combination screws are no exception. The strength grade of the combined screw is divided according to the material of the screw wire and the hardness index of the screw wire. General combination screw materials are divided into stainless steel and iron, stainless steel is divided into stainless steel 201, stainless steel 304 and stainless steel 316 and so on. Iron is divided into three types: low carbon steel, medium carbon steel, and high carbon steel. Carbon steel combination screws refer to iron combination screws. Generally, iron combination screws are classified into grades 4.8, 8.8, 10.9, and 12.9. However, the combination screws of grade 10.9 and grade 12.9 are rarely used in the market, so we will not talk about them here. And the combination screws on the market are more commonly used combination screws of grade 4.8 and 8.8. 4.8 grade combination screws are generally made of 1010A screw wire rods. After the screw wire rods are beaten into screws, they are combined with spring flat washers. After production, this 4.8 grade combination screw does not need to be hardened. Its hardness can reach 4.8. 8.8 grade combination screws are generally made of screw wire 10B21 piers. After the screw and wire piers are made into screws, they are equipped with spring washers and flat washers. They can pass through the automatic elastic flat washer machine to rub the three pieces together. Fasten the spring-flat washer combination on the screw, and the spring-flat washer will not fall off. After the combination screw is produced, it needs to be hardened to make the hardness reach 8.8. After the hardness reaches 8.8, we need to take it for electroplating. In order to prevent hydrogen embrittlement of the spring washer in the 8.8-level combination screw with added hardness, it is easy to break. In this way, we have to perform hydrogen removal treatment on the hardened combined screws, and only after the hydrogen removal can be plated. In short, there are many kinds of standard grades of combined screw strength, but generally only two types are used in the market, one is the 4.8-level combined screw strength, and the other is the 8.8-level combined screw strength. 4.8-level combination screws are the most used in the market and customer needs, and have a wide range of applications. As for the standard strength of 8.8-level combination screws, we generally refer to 8.8-level hexagon socket head combination screws, 8.8-level pan head combination screws, and 8.8-level external hexagon combination screws. These three are more commonly used.
On the surface of the mounting hole on the connector, a 90-degree conical socket is machined, and the head of the flat machine screw is in the socket and is flush with the surface of the connector. Flat machine screws are also used in some occasions with semi-circle head flat machine screws, which are more beautiful and are used for places where a little protrusion is allowed on the surface. Screws play the role of connecting two or more objects and are an indispensable necessity in daily life or industrial manufacturing. There are countersunk head bolts (with grooves) and countersunk head bolts (with tenon).
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 12.9 cylinder head screws, screws with complete specifications, percussion type back bolts, square nuts and nuts and other products, we can provide you with suitable products Your fastener solution.
