Service HotlineIt can be seen that the above processing method can only be used to process a relatively simple retaining ring (that is, only a ring body, which cannot be cut or punched), and the outer surface of the processed retaining ring still cannot be guaranteed to be completely flat.
In addition, the angle aluminum connection structure itself has structural defects of poor torsional and shear resistance, and many projects use larger insulating glass to meet the requirements of architects, resulting in a larger self-weight. In the event of a natural disaster such as an earthquake that will cause the curtain wall to shake violently, the bolts on the angle aluminum are prone to breakage, and the seismic performance is not good. Especially for the beam with the open structure, since the angle aluminum is installed in the opening cavity of the beam, the inertia moment of the beam is small, and the torsion resistance and shear resistance performance of the force are worse.
Therefore, in some cases, workers use a fixed torque wrench to control the tightening degree of the nut, but the fixed torque wrench is not convenient to use, and it needs to be checked frequently. At the same time, because the fixed torque wrench is not a conventional tool, its price is relatively high, which It also leads to its high procurement cost, and frequent verification also makes the later use cost also high.
The circuit board is often the circuit board that plays a major role in electrical equipment, and the main electrical components of the circuit are often integrated on the motherboard. For single-layer circuit motherboards, rivets are used on the circuit motherboard in order to make the components more firmly fixed on the pcb board. In the prior art, the rivets are all set on the circuit board by an automatic riveting machine, which is controlled by an internal program to automatically complete the rivet-setting operation. This internal program is pre-set. If you need to rivet different motherboards, you must change the internal program. If you need to temporarily rivet a circuit board, it will be cumbersome to change the program again. Moreover, this kind of automation equipment is produced on a large scale and is not suitable for temporary operations.
When using screws, if you can understand the mechanical properties of screws first, then you can use screws better. Different types of screws have different mechanical properties, and the different mechanical properties lead to different occasions when screws are used. 1. Self-tapping screws: mechanical performance requirements 1. Heart hardness: standard value HRC28-38. When testing, take the section 1-2 times the diameter of the name from the tail. If the length of the name is too short, it can be embedded first, and then the hardness is measured. 2. Surface hardness: standard MIN HV450. 3. Carburized layer: standard 4#-6#: 0.05-0.18mm, 8#-12#: 0.10-0.23 mm, 14#: 0.13-0.28 mm. The main purpose of carburizing is to enhance the surface hardness and ensure the strength of the teeth. If the decarburization is too deep and the carburization is insufficient, the strength of the teeth will not meet the requirements, that is, the teeth will be damaged during the screw-in test. 4. Torque: standard specification 4#5#6#7#8#10#12#14#A tooth 14212835455696145AB tooth 142128354565102165. 5. Screw-in test: screw the self-tapping screw into a steel plate with a reserved test hole. The self-tapping screw should form a matching thread in the test plate, and the thread of the screw itself will not be deformed or damaged until the end. Tapered threads pass completely through the test plate. The screw-in test is only applicable to AB, B, BP and other types of self-tapping screws. It is stipulated in IFI that the test plate shall be prepared from semi-hard low-carbon cold-rolled steel, and the hardness of the steel plate is 70–85HRB in Rockwell. The standard specification of the steel plate, that is, the thickness, is shown in the table below. The test hole should be punched or drilled, and the tolerance is the specified nominal diameter (see the table below) ± 0.025mm. Specifications 6#7#8#10#12#1/4 Test plate thickness (mm) 1.85-1.953.12-3.234.68-4.84 Aperture (mm) ±0.0252.953.263.454.044.765.50.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: external multi-tooth washers, cover caps, round head bolts, 4.8 grade wing nuts and other products, we can provide you with suitable tightening. piece solution.
