Service HotlineWhen the nut is tightened on the stud, there will inevitably be an empty upstroke. That is, when the nut has not reached the part that needs to be tightened, the nut needs to be twisted on the non-locking (working) part of the front end of the stud by hand or tool, so that the nut runs along the axial direction of the stud and reaches the part to be locked. . When the idling stroke of the thread at the front end of the stud is long or the thread pitch is small, the idling stroke before locking will waste a lot of time, resulting in a huge occupation of personnel or tools.
However, although the existing screws can meet the function of connecting and fastening objects, they are all pressed against the object by the head to achieve the purpose of pressing and fixing. However, due to the small size of the head, it is difficult to press the object firmly. , for this reason, only spacers can be added to increase the pressing area. However, in the assembly process, the gasket is prone to slip off, and it needs to be supported by hand, which brings inconvenience to installation and use; at the same time, sometimes the object to be pressed is only on one side of the screw, and the other side of the screw does not need to be pressed. This results in unnecessary waste of materials, and also occupies a certain space, which brings trouble to the installation of other components.
The existing screw generally includes a round table-shaped nail body with one large end and one small end, a threaded section is provided on the radial circumference of the nail body, a small end of the nail body is provided with an inclined tip, and the large end of the nail body is provided with a nail cover. , generally used on materials that are softer than the screw, and drill into the object to be nailed through its own rotation. When drilling, the thread plays the role of rotary cutting, so that the screw is drilled forward, but when the thread cuts the object to be nailed When it is shaken for a long time, the tightening force of the screw in the axial direction is not enough, it is easy to loosen, and there is a potential safety hazard.
Anchor bolts are also known as stiffened anchor plate anchor bolts, welded anchor bolts, anchor claw anchor bolts, rib plate anchor bolts, anchor bolts, anchor screws, anchor wires, etc. It is specially designed to be buried in the concrete foundation and used as the base for fixing various machines and equipment. Figure 7 anchor bolts are the most commonly used anchor bolts. It is generally made of Q235 steel, with high strength using Q345B or 16Mn material, and also using 40Cr material to process 8.8-strength products, and occasionally using secondary or tertiary rebar. Anchor bolts are divided into wool, thick rod and thin rod. The wool material is the raw material steel, which is directly processed from round steel or wire without modification; thick rods or called A-type, thin rods or B-type, are processed from steel modified into the corresponding required rod diameter. Welded anchor bolts are made of single-headed bolts welded with stiffened iron plates. Its anti-pulling ability is strong. According to the different conditions of use, it can reach 3.6, 4.8, 6.8, 8.8 and other grades respectively. The tensile capacity of 3.6 grade 7-shaped anchor bolts is the tensile capacity of the steel itself. The tensile strength of anchor bolts directly processed from Q345B or 16Mn raw materials can reach a tensile strength of 5.8. The tensile strength of grades 4.8, 5.8, 6.8 and 8.8 refer to the provisions on mechanical properties in GB/T3098.1.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of the quality also contributes to the improvement of the lifespan of the 6-pack.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: small screws, rivet bolts, cap nuts, grade 8 hexagonal thin nuts and other products, we can provide you with suitable fastening products piece solution.
