Service HotlineA kind of screw provided by Yueluo, the rod body of the screw rod has a thread segment, and the two ends of the thread segment are respectively provided with annular and two convex rings. The nominal size of the thread segment, and the distance from the convex ring at the rear end of the screw in the screwing direction to the rod core is greater than the nominal size of the thread segment.
On the other hand, when assembling many pin installation mechanisms, one end of the pin needs to be installed into the hole or arranged in the hole, and then the other end of the pin is applied to the pin through the pin installation mechanism, so that the pin is fixed in the hole. In the hole of the hole type product. This fixing method is not only extremely inefficient. And it is not possible to install multiple pins at once. Especially when exemplified at the other end of the pin, since there is nothing to hold the pin stable when the pin enters the hole type product, when force is applied to the other end of the pin, the pin can easily bend and damage the pin. .
Guangdong Yueluo Hardware Industry Co., Ltd. provides a nut provided by Yueluo, which includes an internal thread. is an arc curve. Compared with the nut of the same type, the normal pressure and friction force of the nut are increased, the thread is not easy to loosen, and the bolt and nut are in surface contact, so it is not easy to cause stress concentration and local material yield, which effectively improves the tightening force of the bolt and nut. Stability, increase fastening reliability.
With the vigorous development of the construction market, fastener-type steel pipe scaffolding and formwork support have been widely used, and a large number of fasteners are used in the fastener-type steel pipe scaffolding and formwork support system. The commonly used fastener structure generally includes a fastener body 1, a blade 2, and a rivet 3 for connecting the fastener body and the blade. An arc-shaped cavity 4 for penetrating the steel pipe is provided between the fastener body and the blade. Figure 1 Right-angle fasteners shown. However, in the process of building construction, the blades of the fasteners have different degrees of cracks and fractures, which lead to the scrapping of the fasteners, or the fasteners are scrapped due to the poor anchoring of the rivets of the fasteners, resulting in a lot of waste, and the fasteners are damaged. There is a large safety construction hazard. However, repairing damaged fasteners entirely by hand has many disadvantages, such as technical difficulty, time-consuming and labor-intensive, and high operating costs. Therefore, researching and designing an auxiliary device for installing rivets in the process of repairing damaged fasteners to reduce labor intensity of workers, improve repair efficiency, and reduce operating costs is a technical problem to be solved urgently by those skilled in the art.
Sometimes, the iron screws are often seen broken, and sometimes, the stainless steel screws are also seen broken. But generally speaking, stainless steel screws rarely break. Because the stainless steel screw wire itself is relatively hard. But under certain circumstances, stainless steel screws can still break. So what are the main reasons for stainless steel screws to break? The reasons for the fracture of stainless steel screws are as follows: 1. The quality of raw materials used for stainless steel screws is poor, and the quality of stainless steel screws is not good. There are many impurities, impure, resulting in insufficient hardness of stainless steel screws. 2. The production process of stainless steel screws. For example, stainless steel screws with eccentric head and eccentricity, and the Q value is too deep and the R position design is too small during the down punching operation during production. 3. The customer uses too much force when using stainless steel screws. Generally, you do a torque test to see how much the minimum breaking force is, and then adjust the torque. Of course, stainless steel screws must be broken for more than three reasons. But the above three reasons are the main reasons for the fracture of stainless steel screws. When the stainless steel screw is found to be broken, it can be checked step by step. Find out what's causing it.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: DIN982 nylon lock nuts, ingot big ears butterfly claw nuts, flat head cross plastic screws, 316 stainless steel and other products, we can provide you with products suitable for you fastener solutions.
