Service HotlineWhen using ordinary hexagon head bolts or ordinary T-bolts with the oval groove structure, the bolts need to be inserted from the back of the groove. When the bolts cannot be inserted from the back of the groove due to the structural limitations of the steel base or the platform itself, it is often necessary to open the installation surface. Large diameter hand holes allow for easy mounting of bolts, which weakens the inherent strength and rigidity of a steel base or platform.
The one-way nut provided by Guangdong Yueluo Hardware Industry Co., Ltd. has the following characteristics: a. It is composed of a screw sleeve 1, a threaded core 2, a cover 3, a spring 4 and a bead 5; b. There is a stop 7 on the outer edge of the core 2 and a ring of grooves 8; c. The screw sleeve 1 is sleeved on the screw core 2; d. 4 is enclosed in hole 6.
The material of the round head three combination screw is divided into iron and stainless steel. The iron ones are made of different iron screw wires. Generally, the wire of the combination screw is 1010, 1018, 10B21 and so on. 10B21 is used to make 8.8 grade combination screws. Like 8.8-grade socket head cap screws, 10B21 wires are often used to make them. When done, go to heat treatment. After heat treatment, remove hydrogen and electroplating. This is to prevent the spring washer of the socket head cap screw from breaking. Stainless steel combination screws, in the combination screw market, generally refer to stainless steel SUS304 combination screws. 201 combination screws generally do very little. Few manufacturers of round head three combination screws produce 201 combination screws. Because the hardness of the screw wire of stainless steel 201 is not well controlled, it is easy to produce cracks. Introduction to the basic knowledge of electroplating round head combination screw electroplating generally refers to the de-plating of iron combination screws. Electroplating is divided into environmental protection and non-environmental protection. Commonly used combination screw electroplating colors include green color zinc, green blue zinc, green white zinc, green nickel, red color, white zinc, white nickel, etc. Cross recessed combination screws, hexagon combination bolts and self-tapping combination screws are used in the same way as the corresponding cross recessed screws, hexagon head bolts and self-tapping screws. The main feature of these combination screws is that they are equipped with corresponding washers, which are very convenient to use.
captive screw is a commonly used pressure riveting part. Usually the captive screws are directly riveted on the motherboard, so as to play the role of fixing the components, and there is a high requirement for the distance between the opening holes on the component. Once the distance between the through holes on the component and the If the distances between the riveting holes on the motherboard do not match, the components cannot be riveted on the motherboard, which will result in defective or scrapped products, thereby increasing production costs and reducing production efficiency.
Generally known bolts refer to screws with a larger diameter. According to this statement, the diameter of screws is much smaller than that of bolts. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat spring washer combination screws, riveting parts BSO bottom hole 6.0, ring nuts, flat head screws and other products, we can provide you with products suitable for you fastener solutions.
