Service HotlineRegardless of stainless steel plate or heat-resistant steel plate, austenitic steel plates have the best comprehensive properties, with sufficient strength, excellent plasticity and low hardness, which is one of the reasons why they are widely used. Austenitic stainless steel is similar to most other metal materials, its tensile strength, yield strength and hardness increase with the decrease of temperature; plasticity decreases with the decrease of temperature. Its tensile strength increases uniformly in the temperature range of 15~80°C. More importantly: as the temperature decreases, the impact toughness of stainless steel screws decreases slowly, and there is no brittle transition temperature. Therefore, stainless steel can maintain sufficient plasticity and toughness at low temperature.
Large, countersunk, and thin rivet nuts can be produced according to different die angles. Then the cold forged rivet nut is degreasing, cleaned and annealed, and then extruded and tapped and surface electroplated. Since the rivet nut is formed by cold extrusion of low carbon steel, it has high mechanical properties. Specifically, the tensile strength of M3 is 250Kg, the shear strength is 140Kg; the tensile strength of M4 is 700Kg, the shear strength is 220Kg; the tensile strength of M5 1100Kg, shear force 380Kg; M6 tensile force 1750Kg, shear force 450Kg; M8 tensile force 2650Kg, shear force 660Kg.
Pedicle screws can be divided into four types: one-way short-tail screw, one-way long-tail screw, universal short-tail screw and universal long-tail screw. Pedicle screws can effectively complete the three-column fixation of the spine and are clinical The most widely used internal fixation method for the treatment of spine-related diseases. Due to the different types of pedicle screws, four different screwdrivers are required to complete the screw insertion. However, the implantation of pedicle screws is performed in a complex three-dimensional space, which has high difficulty and risk. Mis-implantation of screws may cause instability of the internal fixation frame in the early stage, and may cause false joint formation in the later stage. Therefore, in the process of spinal internal fixation, it is necessary to ensure the accurate implantation of pedicle screws is the key to the success of the entire spinal internal fixation, and the selected implanted instruments are particularly important.
When the mechanical components are installed on the concrete foundation, the J-shaped and L-shaped ends of the bolts are embedded in the concrete for use. The tensile capacity of the anchor bolt is the tensile capacity of the round steel itself. The size is equal to the cross-sectional area multiplied by the allowable stress value (Q235B: 140MPa, 16Mn or Q345: 170MPA), which is the allowable tensile capacity at the time of design. The anchor bolts are generally made of Q235 steel, which is smooth and round. Rebar (Q345) is strong, and the thread of the nut is not as easy to be round. For light round anchor bolts, the burial depth is generally 25 times its diameter, and then a 90-degree hook with a length of about 120mm is made. If the bolt diameter is large (such as 45mm) and the buried depth is too deep, a square plate can be welded at the end of the bolt, that is, a large head can be made (but there are certain requirements). The burial depth and hook are all to ensure the friction between the bolt and the foundation, so as not to cause the bolt to be pulled out and damaged.
The contact surface between the existing chassis and the main board is generally not a horizontal plane due to processing reasons, especially the main board is prone to warping deformation. It will increase, resulting in deformation of the motherboard and poor memory contact, affecting normal use.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: knurled aluminum alloy single-layer hand-tightened nuts, ISO7380 screws, 6mm cross-hole splint nuts, iron galvanized screws and other products, we can provide you with Provide the right fastener solution for you.
