Service Hotlinescrew assembly jig comprises a base, a cylinder and a cylinder which are vertically arranged on the base and are arranged opposite to each other, and a sliding plate that can move up and down along the cylinder and the cylinder, the area above the sliding plate is provided with a cylinder, and the four corners pass through the cylinder respectively. Four pneumatic screwdrivers are placed and fixed on the sliding plate, the area of the base is further provided with a fixing plate corresponding to the four pneumatic screwdrivers; one end of the base is also provided with a switch. Guangdong Yueluo Hardware Industry Co., Ltd. can quickly drive multiple screws into the product at the same time, which has the characteristics of high production efficiency and high yield rate.
Generally, the T-bolt structure is common, and its blank shape can be completed at one time on a multi-station cold heading machine. But for T-bolts with relatively rare structures, (for example: the intersection of ¢14x42 cylinder (head) + ¢12 cylinder, the two cylinders form a 90° intersection) due to the special structure, the head Cold forming is difficult, and the traditional processing route is: die casting blank → deburring → turning processing → grinding blank diameter → wire rolling → heat treatment → surface treatment → finished product packaging.
At present, the electrical control boxes of the market regulators all include a box body with built-in circuit board components and a box cover that is fastened together with it. The box cover is mostly fastened on the box body by self-supplied screws. The following problems are: First, there are many electric control lines on the circuit board in the box. When installing the self-supplied screws, the electric control lines may be damaged, which may easily cause a short circuit of the electric control, which is a potential safety hazard; Electric batch and other tools are inconvenient to install and disassemble, and the production cost is high.
The slotted nut needs to be fixed with a cotter pin through the slot of the slotted nut, and the cotter pin must pass through the middle of the screw to fix the slotted nut. Usually, both ends of the screw need to be drilled, the diameter of the hole and the size of the slotted nut. The width and depth of the slot determine the size of the cotter pin. When the selected screw, cotter pin and slotted nut are relatively matched, the nut is fixed by the screw, so that the slotted nut does not loosen. This hexagonal slotted nut has the characteristics of high strength and is not easy to loosen when subjected to vibration. It is mainly used in occasions with vibration and shock, such as front and rear axles of automobiles, lifting equipment, presses and die-casting machines.
Existing wood screws are composed of a threaded portion with a tapered angle and arranged along a tapered stem and a screw head. The head of the screw can be a countersunk head, hemispherical, or other shapes, and the head of the screw has a groove that fits with the tool, a word groove, and a concave cross groove. The taper angle of existing wood screws is either 45 degrees or 60 degrees, and the front end of the taper angle is a pointed point formed by a rotating thread. The existing wood screws have the following three deficiencies in use. Because the taper angle is 45 degrees or 60 degrees, and the thread angle is 64 degrees, the resistance when entering the material is relatively large, so the existing wood screws are manually screwed. It is difficult to screw in, especially when it is used for hardwood materials, and it often happens that the groove of the screw head is screwed out; A large lateral moment will be formed when the screw is screwed, which is prone to the problem of deviation from the position; in addition, because the existing screw is tapered, it will be subjected to both radial force and axial force when entering the material, and its stress state It is more complicated, so it is easy to cause the cracked wood material to burst, and even cause the material to have longitudinal cracks and be unusable.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: high-brightness bolts, blank nuts, triangular bolts, shock-proof washers and other products, we can provide you with suitable fastener solutions for you.
