Service Hotlinehand screw is a screw with a plastic head, and the user fixes the hand screw by turning the plastic head by hand. At present, a hand screw is disclosed in the market publication number CN202203253U, which includes a plastic head and a screw rod, the plastic head and the screw rod are connected together, and the height of the plastic head is higher than that of an ordinary screw, and the height is 12 cm. The screw of the hand screw is fixed in the plastic head by glue. After a period of use, the aging of the glue leads to the loosening of the screw and the plastic head. When the plastic head is stressed, the screw rod comes out of the plastic head, which affects the normal use of the hand screw.
Yueluo's thin plate rivet method, the thickness of the metal thin plate is less than 0.8mm. The convex rib extrudes the metal sheet adjacent to the rivet hole. The protruding rib is annular, and the protruding rib surrounds the rivet. The rivet head is provided with a positioning structure, the rivet head is provided with a positioning structure for docking the positioning structure, and the positioning structure and the positioning structure are mutually butted through the rivet to align the convex rib with the rivet
Screws are very small screws used for indispensable industrial necessities in daily life, such as cameras, glasses, clocks, electronics, etc.; general screws for televisions, electrical products, musical instruments, furniture, etc.; large screws are used for engineering, construction, and bridges; Transportation equipment, airplanes, trams, automobiles, etc. use large and small screws together. At present, in the machine assembly production line, when the flat washers, spring washers and screws are matched during the screw assembly process, the flat washers, spring washers and screws are easy to fall into the product due to their small size, resulting in low screw matching efficiency. If there are flat washers, spring washers, screws, etc. that fall into the product and are not found in time and left inside the product, it may cause damage to the machine structure, and even cause casualties in serious cases.
As we all know, when installing the outdoor unit of the air conditioner, most of the installers need to hang it on the outer wall. When tightening the machine foot screws, they all need to lean out of the window or climb out the whole person, and use a wrench to tighten it. . Therefore, it is difficult for the installer to operate, and it is easy to drop the installation materials such as screws and nuts, which is not only a waste of materials, but also easy to hurt personnel. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to solve the above problems, and provide a safe and labor-saving air conditioner outdoor unit machine foot screw installer that the installer does not have to lean out of the window or climb out of the room, and the installation materials are not easy to fall.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 304 plate rivets, countersunk head machine screws, spring steel washers, through-hole internal thread 7-star handle hand-tightening nuts and other products, we can help you Provide the right fastener solution for you.
