Service HotlineGuangdong Yueluo Hardware Industry Co., Ltd. relates to a square nut fastener for cable bridge installation, which is characterized in that it includes an upper plate body and a U-shaped jacket, and the upper plate body is provided with a downwardly protruding connecting cylinder, The two side plates of the U-shaped jacket are connected to the connecting cylinder, and the center line of the two side plates is located on the center line in the length direction of the upper plate body; the bottom of the U-shaped jacket is a wave-shaped elastic plate, which is a wave-shaped elastic plate It is fixedly connected on the two side plates, and the space enclosed by the two side plates of the U-shaped jacket, the wave-shaped elastic plate and the bottom of the connecting cylinder is the installation position of the square nut. Guangdong Yueluo Hardware Industry Co., Ltd. has a simple and reasonable structure, and is extremely convenient and flexible to operate; it does not occupy the bottom space of the C-shaped steel after installation, which increases the variety of installation, and can be applied to square nuts of different thicknesses, and the installation is firm.
Bolt and nut fasteners are widely used fasteners, which can be used in mechanical products as well as daily craft industrial products, such as plastic packaging boxes, plastic packaging boxes, paper packaging boxes, paper packaging boxes, etc. . When bolt and nut fasteners are used in daily craft industrial products, the requirements for the degree of tightening are generally low, but they are required to be easy to install and use. When assembling the existing bolt and nut fasteners, it is generally necessary to manually twist the bolt or the nut several times until the two are tightened, which takes time and causes inconvenience in daily life. Lower, it is manifested as an increase in labor costs. SUMMARY OF THE INVENTION The main purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bolt and nut fastener that is easy to install in view of the above-mentioned deficiencies of the prior art. The two are assembled and fastened, which is convenient to use.
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 447N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
The advantages of the pressure riveting nut: 1. The length guarantee of the distance range is realized, which greatly simplifies the assembly process and speeds up the production progress of the assembled spacing panel and accessories; 2. The back of the plate is completely embedded and flat, while ensuring the head of the nut column The plane is smooth with the plate; 3. The raw material is free-cutting iron or free-cutting stainless steel; the technical guide for the application of the pressure riveting standoff: 1. When selecting the standoff, it must be based on the thickness of the plate used, the exact size range, and the hardness of the low-carbon steel plate must be less than 70RB, the hardness of stainless steel plate must be less than 80RB. 2. The surface of free-cutting iron is treated, and the stainless steel maintains its original color. Users can order according to the model and specifications in the table according to their needs, or they can also make special orders according to their needs. 3. The hole size of the plate must be processed according to the tolerance size of 0-+0.075mm, and punching is recommended. 4. The installation must be realized by press riveting operation, and it must not be knocked in by impact. 5. When the material is stainless steel, the tail number should be marked with S. 6. The end face of the nut column is represented by C. 7. The length of the through-hole nut column is full wire below 10mm. If it is above 10mm, it can be reamed on the hexagonal end face (type I) or the round end face (type II).
As we all know, bolt and nut kits are commonly used fastening parts, but when ordinary bolt fasteners are used in a large number of parts, because the nuts and bolts are engaged by threads, manual or machine tightening is required, and during installation, It is easy to slip, and the bolts need to be operated in both directions, and a pair of bolts and nuts cannot be installed quickly, which reduces the installation efficiency.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: smooth flat head screws, hexagonal screw caps, chassis screws, thin button screws and other products, we can provide you with suitable fasteners for you solution.
