Service HotlineBlind rivets are a type of flying rivets for single-sided riveting, but they must be riveted manually, electrically, and automatically using special tools. This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets and must be riveted from both sides, so it is widely used in construction, automobiles, ships, aircraft, machinery, electrical appliances, furniture and other products.
In the current production process, the inner wall of the circlip is quantitatively and evenly lubricated, and then the rotating shaft is inserted into the circlip, so that the rotating axis can rotate in the circlip, thereby realizing the rotation function of the sun visor. However, since the circlip is tightly fitted with the rotating shaft, during the insertion process of the rotating shaft, the front end of the circlip can easily push the grease from the opening at one end of the circlip to the opening on the other end of the circlip, so that the rotating axis and the inner wall of the circlip are easily connected. There is little or no grease left between them, which can easily lead to a lack of lubrication between the shaft and the circlip, and dry friction between the shaft and the circlip, resulting in a series of problems such as abnormal noise, difficult operation, and poor durability.
NPT, PT, G are all pipe threads. NPT is the abbreviation of National (American) Pipe Thread, which belongs to the American standard 60-degree taper pipe thread, which is used in North America. National standards can be found in GB/T12716-1991 PT is the abbreviation of Pipe Thread, which is a 55-degree sealed conical pipe thread, which belongs to the Whitworth thread family and is mostly used in Europe and the Commonwealth of Nations. Commonly used in water and gas pipe industry, the taper is specified as 1:16. The national standard can be found in GB/T7306-2000 G is a 55 degree non-threaded sealing pipe thread, which belongs to the Whitworth thread family. Marked as G stands for cylindrical thread. National standards can be found in GB/T7307-2001 In addition, the 1/4, 1/2, 1/8 marks in the thread refer to the diameter of the pipe, and the unit is inches. People in the industry usually refer to thread size in points, 1 inch equals 8 points, 1/4 inch is 2 points, and so on. G seems to be the general name for pipe threads (Guan), and the division of 55 and 60 degrees is functional, commonly known as pipe circle. That is, the thread is machined from a cylindrical surface. ZG is commonly known as pipe cone, that is, the thread is made of a conical surface. The general water pipe joints are like this. Rc means conical internal thread ZG means taper pipe thread, 3/4 means inch mark, which is 3/4 inch conical pipe Thread, there is in the Hardware Manual. The national standard stipulates that the major diameter of ZG 3/4 thread is 26.44 mm. Please refer to Metric, American and British Thread Standard Manual (Third Edition). Its representation method should be: ZG 3 /4″. Among them (〃) is the representative symbol for inches. One inch is equal to 8 inches. The origin of 3/4 is 6/8=3/4. Commonly known as 6 points. Similarly, the major diameter of ZG 1/2″ thread≈21 mm. Commonly known as 4 points. ZG 1″ thread diameter ≈ 33 mm. Commonly known as 1 inch. ZG 1 1/2″ thread pipe outer diameter ≈ 48 mm. Commonly known as 1 inch and a half. Taper pipe thread is very similar to pipe thread, the difference is Only in the taper. Note that the basic size of the pipe thread and ordinary thread is different. DN is the nominal diameter
In the process of completing the adjustment of the position of the object, the nut will move up and down with the entry and exit of the screw, and it cannot make a sound for people to perceive, and it cannot provide people with a position change distance through the action of rotation.
The lifting ring screws are generally not surface treated, but according to the requirements, surface treatment such as galvanized passivation and chrome plating can be carried out, and it is specified in GB5267-85. The chemical composition and mechanical properties of the material should be treated immediately after electro-galvanizing. The test methods are specified in GB699. During routine inspection, the grain size test may not be advanced, and the grain size test method shall be in accordance with the provisions of YB27. Thread inspection is performed with thread gauges and smooth limit gauges or universal energy tools.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: anti-slip toothed nuts, hexagonal pan head bolts, claw-shaped butterfly nuts, stainless steel hexagonal bolts and other products, we can provide you with suitable products for you. Fastener Solutions.
