Service HotlineThe locking effect of the spring washer is general, and the important parts are used as little or not as possible, and the self-locking structure is adopted. For spring washers used for high-speed tightening (pneumatic or electric), it is best to use surface phosphating washers to improve their anti-wear performance, otherwise it is easy to burn out or open mouth due to friction and heat, and even damage the surface of the connected parts. For thin plate joints, spring washer construction should not be used. According to statistics, spring washers are used less and less in automobiles.
At present, injection molding screws are widely used in various electronic and automotive components, including a body, the middle of which is provided with a through hole 3, the body head 1 has a hexagonal cross-section, and the tail 2 is provided with screw teeth. When in use, the middle through hole 3 of the main body will first put the wire harness, and then fix it by injection molding from the head I, and the threads of the tail 11 should be connected and installed with other components. Because the head I of the main body is hexagonal, the torque provided after injection molding is insufficient. Therefore, after the external thread is installed and connected with other components, the head is prone to slip, the installation is not reliable, and there is no push-pull force, resulting in product failure and increased safety hazards.
The conventional auger bit structure 1 includes a rod body 11, a screw head 12 provided on one end of the rod body 11, a drill tail 13 provided on the other end of the rod body 11, and a plurality of threads 14 arranged around the rod body 11; Wherein, the periphery of the drill tail 13 defines a parting line 15, and the parting line 15 makes the drill tail 13 symmetrically divided into a side 131 and a side 132, and a cutting end 133 is formed at the junction of the end of the side 131 and the end of the side 132, respectively. The cutting end 133 is concavely provided with a quarter-turn chip flute 134 in the same direction of the helix, and the edge 132 continues the chip flute 134 and has a quarter-turn chip flute 135 with different helical curvatures. , using the chip groove 134 and the chip groove 135 to be connected by different helical curvatures, so that the drill tail 13 can form a symmetrical and complete chip groove of 190 degrees.
Basic parameter broadcast name 1. Machine screw 2. Self-tapping screw 3. Drilling screw 4. Wallboard screw 5. Fiberboard screw 6. Wood screw 7. Hexagon wood screw 8. Non-prolapse screw 9. Combination screw 10. Micro screw 11 . Furniture screws 12. Electronic screws 13. Chain screw head type: 1. Hexagon head (hexagon head) 2. Hexagon head with flange (hexagon head with flange) 3. Square head (square head) 4. T-shaped head T head (hammer head 5. mushroom head (truss head) 6. cylindrical head (cheese head) 7. round head (round head) 8. pan head (pan head) 9. countersunk head (flat head) 10 .Half countersunk head raised countersunk head ( Groove type: 1. Flat 2. Inner triangle 3. Inner corner square 4. Cross 5. Rice shape 6. Flower shape 7. Plum blossom 8. Flower shape 9. Special shape 10. Inner hexagon
As my digital TV technology becomes more and more mature, more and more people with digital-to-analog signal conversion function enter people's lives. Therefore, the number of production and processing is also increasing day by day. There are many requirements for the form, reliability and cost of PCB fixing screws in production. One of the existing fixing methods is to fix by means of bolts and nuts. The operation steps are to place the PCB board on the inner threaded copper column connected to the casing, and pass through the bolts with fine teeth. Screw holes on the PCB board, and then fix them on the copper posts with nuts. The connection method of this solution is reliable, but its manufacturing cost is high, and the copper column and the metal shell need to be screwed together, resulting in low production efficiency and high cost. In addition, there is also a common way that the PCB is supported by a plastic column, and the self-tapping screw is passed through the screw hole on the PCB board, and the PCB board and the metal bottom shell are connected by the self-tapping thread on the screw. The main disadvantage of this solution is that after the screw is fixed on the metal shell, the screw head is exposed at the bottom of the machine. If the user is not careful during use, the hand scratching phenomenon will occur, which will bring changes and harm to the user's use. . And when the machine slides on the desktop, if the screw head is too exposed, it will scratch the desktop. Therefore, how to provide a PCB fixing method with convenient operation, reliable connection and low production cost is a technical problem to be solved urgently in the industry.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: all-metal hexagonal flange face nuts, cross countersunk head to lock splint to knock screws and nuts, hexagonal three combination bolts, Q254 screws and other products, we can Provide you with the right fastener solution for you.
