Service HotlineThe electroplating of cross recessed screws generally refers to the electroplating of iron cross recessed screws. Stainless steel cross recessed screws are rarely electroplated. The electroplating colors of cross recessed screws are divided into environmental protection and non-environmental protection. Environmental protection blue zinc, environmental protection color zinc, environmental protection black zinc, environmental protection white nickel, etc., non-environmental protection includes white nickel, white zinc, color zinc, black zinc, black nickel, black cladding, blue zinc.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bayonet which is a T-shaped cylindrical pin with a misaligned through hole at the head, and a bayonet spring which is a ring-shaped spring steel wire whose ends are staggered. The retaining ring is clamped by the bayonet pin to fix the stop sleeve and the pin shaft together. A hydraulic excavator pin stopper with high disassembly and assembly efficiency and no need for a wrench. The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is such that it includes a latch, a stop sleeve, a pin, a bayonet, and a circlip. The staggered end is clamped into the misaligned through hole of the plug, and screwed on the bottom of the stopper sleeve to fix the stopper sleeve and the pin shaft together. The latch is composed of a bayonet pin and a circlip, the circlip is screwed around the through hole of the bayonet pin to the root of the bayonet pin, and the stopper sleeve is tightly wrapped around the pin shaft, and the circlip is tightly against the bayonet pin. The head of the bayonet pin has two T-shaped cylindrical pins with staggered through holes, and the circlip is an annular spring steel wire whose ends are staggered. By adopting the pin shaft stopping method of the above technical scheme, it is extremely convenient and quick to disassemble and assemble the pin shaft. The bolt of Guangdong Yueluo Hardware Industry Co., Ltd. is only composed of a T-shaped cylindrical pin with two staggered through holes in the head and a ring-shaped spring steel wire with staggered ends. The structure is simple, convenient to manufacture, low cost and obvious. It is an excavator pin stop method with high disassembly and assembly efficiency, no need for a wrench and low manufacturing cost.
In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35 , and the screws enter the screw accommodating hole 43 from the discharge port through the guide rail 6 . The slotting is carried out, which improves the efficiency and saves the labor cost.
Other names of lock nut: root nut, locknut, nut. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures. There are also three types of lock nuts: The first is to use two identical nuts to screw on the same bolt, and add a tightening torque between the two nuts to make the bolt connection reliable. The second is a special anti-loosening nut, which needs to be used together with a kind of anti-loosening washer. The special lock nut is not a hexagonal nut, but a medium round nut. There are 3, 4, 6 or 8 notches on the circumference of the nut (depending on the size of the nut and the product series of the manufacturer). Several notches are both the focal point of the tightening tool and the snap-in of the lock washer bayonet. The third type is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, which are distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to give the thread Apply a centripetal force to prevent the locknut from loosening. The better quality lock nut sold on the market is inlaid with a small copper block that is consistent with the thread of the lock nut on the inner surface of the nut to prevent the radial jacking screw from directly contacting the locked thread and damaging the latter. . This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The second anti-loosening method is more reliable than the first, but the structure is relatively complex. Compared with the first two, the third clock has the characteristics of better anti-loosening effect, simpler and more beautiful structure and smaller axial size.
Heat treatment broadcast quenching and tempering HB220-270, nitriding HRC>65 foreign use titanium carbide coating method to improve the corrosion resistance of the screw surface, but according to reports, its wear resistance is not good enough. A series of measures have been taken abroad to improve the wear resistance and corrosion resistance of the screw. One way is to use highly wear-resistant and corrosion-resistant alloy steel. Such as 34CrAlNi, 31CrMo12 and so on. There is also a method of spraying Xaloy alloy on the surface of the screw. This Xaloy alloy has high wear and corrosion resistance.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: nylon cap nuts, cross hexagon bolts, nail welding bolts, precision fastener screws and other products, we can provide you with fastening suitable for you piece solution.
