Service HotlineIn recent years, a spring pin connection structure has appeared in the connection between the beam and the column: a pin hole is arranged on the column, and a spring pin is arranged at the end of the beam. When installing, the spring pin can be inserted into the pin hole. However, when more than two spring pins are used, if the spring pins are slightly deviated from the pin holes, it is difficult to spring into the pin holes; and if the pin holes are drilled larger, although the spring pins are easy to spring in, it will cause the spring pins to spring into the pin holes. Looseness with pin hole. In addition, after the spring pin is used for a long time, the spring is easily corroded and fractured, which also leads to structural instability and difficulty in disassembling the beam.
The semicircular key is a kind of key, the upper surface is a plane, the lower surface is a semicircular arc surface, the two sides are parallel, commonly known as the crescent key. It is basically the same as the flat key connection method, but it is more convenient to manufacture and disassemble than the flat key, and is especially suitable for the connection between the tapered shaft and the hub. The half-round key transmits torque on the side, but the keyway is deep, which weakens the shaft greatly. Due to the deep keyway, the bottom of the keyway is easily deformed after the shaft is heat treated. Therefore, when the semicircular key and the keyway are assembled in a transitional fit relationship, the interference between the lower part of the semicircular key and the bottom of the keyway often occurs, resulting in difficult or impossible assembly. Assembly situation. In order to solve the above technical problems, the current method is to make the thickness of the semicircular key appropriately thin, so that the semicircular key and the keyway are clearance fit, which brings about a large gap between the upper part of the semicircular key and the keyway, and the semicircular key is in operation. Difficult to locate in the keyway, affecting smooth transmission.
A kind of screw provided by Yueluo, the rod body of the screw rod has a thread segment, and the two ends of the thread segment are respectively provided with annular and two convex rings. The nominal size of the thread segment, and the distance from the convex ring at the rear end of the screw in the screwing direction to the rod core is greater than the nominal size of the thread segment.
Most electrical appliance manufacturers only require the size and riveting gap to be tested for riveted contact components. There is no clear requirement for riveting strength. Only a few manufacturers perform torsion testing on riveting strength. The torque detection method is as follows: use a saw blade to open a one-shaped groove on the rivet head of the riveted contact element, and then insert a torque wrench into the one-shaped open groove to rotate, and measure the torque value. Because most of the electrical contacts are made of copper-silver alloy, the strength is low, and it is easy to slip during the test, and when a saw blade is used to open the one-shaped groove, the width and depth cannot be accurately positioned, so the measured value fluctuates greatly. , has always been an unsolvable technical problem in the industry.
The structure of Guangdong Yueluo Hardware Industry Co., Ltd. is as follows. Figure 1 is a schematic diagram of the structure of the existing pin shaft stop mode of a general excavator. Figure 2 is a schematic structural diagram of the pin shaft stop used by Guangdong Yueluo Hardware Industry Co., Ltd. for applying the bolt of Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 3 is the left side view according to Fig. 2 of the bolt used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 4 is the front view of Guangdong Yueluo Hardware Industrial Co., Ltd., which is used for the pin shaft stopper to insert the pin into the pin and form the pin of the pin structure. Fig. 5 is the left side view of Guangdong Yueluo Hardware Industry Co., Ltd., which is used for the pin shaft stopper to insert the pin into the pin and form the pin of the pin structure. Fig. 6 is a front view of the bayonet of the latch used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 7 is a top view of a bayonet of a latch used for pin stop by Guangdong Yueluo Hardware Industry Co., Ltd. Fig. 8 is the front view of the circlip of the latch used by Guangdong Yueluo Hardware Industry Co., Ltd. for pin stop. [0017] FIG. 9 is a top view of the circlip of the bolt that Guangdong Yueluo Hardware Industrial Co., Ltd. is used for pin-stopping. In Figures 1 to 9, the latch (1), the retaining sleeve (2), the pin shaft (3), the bayonet (4), the circlip (5), the misaligned through hole (6), and the misaligned end head (7).
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: motherboard isolation copper nut column, heavy-duty flat washers, dish-shaped butterfly cone single-sided, toothed screws and other products, we can provide you with suitable products Your fastener solution.
