Service HotlineThe flat key transmits torque on the side, has good neutrality, is easy to assemble and disassemble, and cannot realize the axial fixation of the parts on the shaft. Ordinary flat key: Type A, Type B, Type C, Type A is used for shaft grooves machined by end mills. The key is well fixed axially in the groove, but the stress concentration caused by the groove on the shaft is large; Type B is used for disc milling cutters. The machined shaft groove, the stress concentration of the shaft is small; the C type is used for the shaft end; it is suitable for high-speed, high-precision or occasions under variable load and impact, such as fixing gears, sprockets and other rotating parts on the shaft. Guided flat key: The key is fixed on the shaft with a screw, the key and the hub groove are in dynamic fit, and the parts on the shaft can move axially. For the convenience of starting the key, there is a key-starting screw hole. Use the occasions where the axial movement of the parts on the shaft is not large, such as the slip gear in the gearbox. Feather key: The key is fixed on the axle, and the parts on the shaft can move axially with the key; it is used in the occasions where the axial movement of the parts on the shaft is large;
For hexagonal nuts, the commonly used standards are: GB52, GB6170, GB6172 and DIN934. The main differences between them are: the thickness of GB6170 is thicker than that of GB52, GB6172 and DIN934, commonly known as thick nuts. The other is the difference between the opposite sides, the opposite sides of DIN934, GB6170 and GB6172 in the M8 nut series are 13MM smaller than the opposite side 14MM of GB52, and the opposite sides of M10 nuts, DIN934 and GB52 are 17MM. The opposite side of GB6170 and GB6172 should be 1MM larger, M12 nut, DIN934, GB52's opposite side is 19MM larger than GB6170 and GB6172's opposite side 18MM is 1MM larger. For M14 nuts, the opposite side of DIN934 and GB52 is 22MM, which is 1MM larger than the opposite side of GB6170 and GB6172, which is 21MM. The other is the M22 nut. The opposite side of DIN934 and GB52 is 32MM, which is 2MM smaller than the opposite side of GB6170 and GB6172, which is 34MM. (Besides the thickness of GB6170 and GB6172 are the same, the width of the opposite side is exactly the same) The rest of the specifications can be used in general without considering the thickness.
At present, the known automatic nail feeding screws are composed of the traditional hand-held electric drill modified electric screw and the automatic nail feeding device, in which the screw head cannot be moved and the angle can be changed. It is difficult to complete the installation due to the obstruction, so a multi-directional screw with a movable and rotatable screw head is required.
In the prior art, the screw suction device can be implemented in the following two ways. One is to use a magnet to magnetize the electric bit head, and the electric bit head is used to approach the screw, and the screw is stuck by the electric bit head, so that the function of picking up the screw can be realized; The vacuum generator is used to form a negative pressure in the screw guide groove, and the screw is sucked into the tube to realize the screw pickup. The disadvantage of this solution is that in the process of picking up the screws, the grooves of the screws cannot be aligned, which leads to the deviation or leakage of the screws. The disadvantage of this solution is that the screw with an aspect ratio of less than 1.8 is prone to suction and skew, and the stability is not high. It can be seen that the existing technology still needs to be improved and developed.
④ Screw tooth type A: Self-tapping sharp tail (Japanese standard type 1) sparse AB: Self-tapping sharp tail (Japanese standard type 4) dense; B: Self-tapping flat tail (Japanese standard type 2) sparse; C: Self-tapping Tapping flat tail (the third type of Japanese standard) dense; P: double wire teeth Type triangle teeth CCT: C type triangle teeth PTT: P type triangle teeth STT: S type triangle teeth
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: self-locking lock nuts, industrial aluminum fitting nuts, anti-thread locking lock-proof nuts, carbon steel inch bolts and other products. Provide you with the right fastener solution for you.
